aiot/waterDataPreprocessing/monitoringDataProcessing/preliminaryDataProcessing.h

/*
 * bfin_serial.h - Blackfin UART/Serial definitions
 *
 * Copyright 2006-2010 Analog Devices Inc.
 *
 * Licensed under the GPL-2 or later.
 */

#ifndef __BFIN_ASM_SERIAL_H__
#define __BFIN_ASM_SERIAL_H__

#include <linux/serial_core.h>
#include <linux/spinlock.h>
#include <mach/anomaly.h>
#include <mach/bfin_serial.h>

#if defined(CONFIG_BFIN_UART0_CTSRTS) || \
    defined(CONFIG_BFIN_UART1_CTSRTS) || \
    defined(CONFIG_BFIN_UART2_CTSRTS) || \
    defined(CONFIG_BFIN_UART3_CTSRTS)
# if defined(BFIN_UART_BF54X_STYLE) || defined(BFIN_UART_BF60X_STYLE)
#  define CONFIG_SERIAL_BFIN_HARD_CTSRTS
# else
#  define CONFIG_SERIAL_BFIN_CTSRTS
# endif
#endif

struct circ_buf;
struct timer_list;
struct work_struct;

struct bfin_serial_port {
	struct uart_port port;
	unsigned int old_status;
	int tx_irq;
	int rx_irq;
	int status_irq;
#ifndef BFIN_UART_BF54X_STYLE
	unsigned int lsr;
#endif
#ifdef CONFIG_SERIAL_BFIN_DMA
	int tx_done;
	int tx_count;
	struct circ_buf rx_dma_buf;
	struct timer_list rx_dma_timer;
	int rx_dma_nrows;
	spinlock_t rx_lock;
	unsigned int tx_dma_channel;
	unsigned int rx_dma_channel;
	struct work_struct tx_dma_workqueue;
#elif ANOMALY_05000363
	unsigned int anomaly_threshold;
#endif
#if defined(CONFIG_SERIAL_BFIN_CTSRTS) || \
	defined(CONFIG_SERIAL_BFIN_HARD_CTSRTS)
	int cts_pin;
	int rts_pin;
#endif
};

#ifdef BFIN_UART_BF60X_STYLE

/* UART_CTL Masks */
#define UCEN                     0x1  /* Enable UARTx Clocks */
#define LOOP_ENA                 0x2  /* Loopback Mode Enable */
#define UMOD_MDB                 0x10  /* Enable MDB Mode */
#define UMOD_IRDA                0x20  /* Enable IrDA Mode */
#define UMOD_MASK                0x30  /* Uart Mode Mask */
#define WLS(x)                   (((x-5) & 0x03) << 8)  /* Word Length Select */
#define WLS_MASK                 0x300  /* Word length Select Mask */
#define WLS_OFFSET               8      /* Word length Select Offset */
#define STB                      0x1000  /* Stop Bits */
#define STBH                     0x2000  /* Half Stop Bits */
#define PEN                      0x4000  /* Parity Enable */
#define EPS                      0x8000  /* Even Parity Select */
#define STP                      0x10000  /* Stick Parity */
#define FPE                      0x20000  /* Force Parity Error On Transmit */
#define FFE                      0x40000  /* Force Framing Error On Transmit */
#define SB                       0x80000  /* Set Break */
#define LCR_MASK		 (SB | STP | EPS | PEN | STB | WLS_MASK)
#define FCPOL                    0x400000  /* Flow Control Pin Polarity */
#define RPOLC                    0x800000  /* IrDA RX Polarity Change */
#define TPOLC                    0x1000000  /* IrDA TX Polarity Change */
#define MRTS                     0x2000000  /* Manual Request To Send */
#define XOFF                     0x4000000  /* Transmitter Off */
#define ARTS                     0x8000000  /* Automatic Request To Send */
#define ACTS                     0x10000000  /* Automatic Clear To Send */
#define RFIT                     0x20000000  /* Receive FIFO IRQ Threshold */
#define RFRT                     0x40000000  /* Receive FIFO RTS Threshold */

/* UART_STAT Masks */
#define DR                       0x01  /* Data Ready */
#define OE                       0x02  /* Overrun Error */
#define PE                       0x04  /* Parity Error */
#define FE                       0x08  /* Framing Error */
#define BI                       0x10  /* Break Interrupt */
#define THRE                     0x20  /* THR Empty */
#define TEMT                     0x80  /* TSR and UART_THR Empty */
#define TFI                      0x100  /* Transmission Finished Indicator */

#define ASTKY                    0x200  /* Address Sticky */
#define ADDR                     0x400  /* Address bit status */
#define RO			 0x800  /* Reception Ongoing */
#define SCTS                     0x1000  /* Sticky CTS */
#define CTS                      0x10000  /* Clear To Send */
#define RFCS                     0x20000  /* Receive FIFO Count Status */

/* UART_CLOCK Masks */
#define EDBO                     0x80000000 /* Enable Devide by One */

#else /* BFIN_UART_BF60X_STYLE */

/* UART_LCR Masks */
#define WLS(x)                   (((x)-5) & 0x03)  /* Word Length Select */
#define WLS_MASK                 0x03  /* Word length Select Mask */
#define WLS_OFFSET               0     /* Word length Select Offset */
#define STB                      0x04  /* Stop Bits */
#define PEN                      0x08  /* Parity Enable */
#define EPS                      0x10  /* Even Parity Select */
#define STP                      0x20  /* Stick Parity */
#define SB                       0x40  /* Set Break */
#define DLAB                     0x80  /* Divisor Latch Access */
#define LCR_MASK		 (SB | STP | EPS | PEN | STB | WLS_MASK)

/* UART_LSR Masks */
#define DR                       0x01  /* Data Ready */
#define OE                       0x02  /* Overrun Error */
#define PE                       0x04  /* Parity Error */
#define FE                       0x08  /* Framing Error */
#define BI                       0x10  /* Break Interrupt */
#define THRE                     0x20  /* THR Empty */
#define TEMT                     0x40  /* TSR and UART_THR Empty */
#define TFI                      0x80  /* Transmission Finished Indicator */

/* UART_MCR Masks */
#define XOFF                     0x01  /* Transmitter Off */
#define MRTS                     0x02  /* Manual Request To Send */
#define RFIT                     0x04  /* Receive FIFO IRQ Threshold */
#define RFRT                     0x08  /* Receive FIFO RTS Threshold */
#define LOOP_ENA                 0x10  /* Loopback Mode Enable */
#define FCPOL                    0x20  /* Flow Control Pin Polarity */
#define ARTS                     0x40  /* Automatic Request To Send */
#define ACTS                     0x80  /* Automatic Clear To Send */

/* UART_MSR Masks */
#define SCTS                     0x01  /* Sticky CTS */
#define CTS                      0x10  /* Clear To Send */
#define RFCS                     0x20  /* Receive FIFO Count Status */

/* UART_GCTL Masks */
#define UCEN                     0x01  /* Enable UARTx Clocks */
#define UMOD_IRDA                0x02  /* Enable IrDA Mode */
#define UMOD_MASK                0x02  /* Uart Mode Mask */
#define TPOLC                    0x04  /* IrDA TX Polarity Change */
#define RPOLC                    0x08  /* IrDA RX Polarity Change */
#define FPE                      0x10  /* Force Parity Error On Transmit */
#define FFE                      0x20  /* Force Framing Error On Transmit */

#endif /* BFIN_UART_BF60X_STYLE */

/* UART_IER Masks */
#define ERBFI                    0x01  /* Enable Receive Buffer Full Interrupt */