aiot/waterInvestigationHiddenDanger/analysisOfLeakageHiddenDanger/analysisOfLiquidLevelData.c

/*
 * armadillo 800 eva board support
 *
 * Copyright (C) 2012 Renesas Solutions Corp.
 * Copyright (C) 2012 Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
 *
 * This program is free software; you can redistribute it and/or modify
 * it under the terms of the GNU General Public License as published by
 * the Free Software Foundation; version 2 of the License.
 *
 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA  02110-1301  USA
 *
 */

#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/kernel.h>
#include <linux/input.h>
#include <linux/irq.h>
#include <linux/platform_device.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/sh_eth.h>
#include <linux/videodev2.h>
#include <linux/usb/renesas_usbhs.h>
#include <linux/mfd/tmio.h>
#include <linux/mmc/host.h>
#include <linux/mmc/sh_mmcif.h>
#include <linux/mmc/sh_mobile_sdhi.h>
#include <linux/i2c-gpio.h>
#include <mach/common.h>
#include <mach/irqs.h>
#include <mach/r8a7740.h>
#include <media/mt9t112.h>
#include <media/sh_mobile_ceu.h>
#include <media/soc_camera.h>
#include <asm/page.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/time.h>
#include <asm/hardware/cache-l2x0.h>
#include <video/sh_mobile_lcdc.h>
#include <video/sh_mobile_hdmi.h>
#include <sound/sh_fsi.h>
#include <sound/simple_card.h>

#include "sh-gpio.h"

/*
 * CON1		Camera Module
 * CON2		Extension Bus
 * CON3		HDMI Output
 * CON4		Composite Video Output
 * CON5		H-UDI JTAG
 * CON6		ARM JTAG
 * CON7		SD1
 * CON8		SD2
 * CON9		RTC BackUp
 * CON10	Monaural Mic Input
 * CON11	Stereo Headphone Output
 * CON12	Audio Line Output(L)
 * CON13	Audio Line Output(R)
 * CON14	AWL13 Module
 * CON15	Extension
 * CON16	LCD1
 * CON17	LCD2
 * CON19	Power Input
 * CON20	USB1
 * CON21	USB2
 * CON22	Serial
 * CON23	LAN
 * CON24	USB3
 * LED1		Camera LED(Yellow)
 * LED2		Power LED (Green)
 * ED3-LED6	User LED(Yellow)
 * LED7		LAN link LED(Green)
 * LED8		LAN activity LED(Yellow)
 */

/*
 * DipSwitch
 *
 *                    SW1
 *
 * -12345678-+---------------+----------------------------
 *  1        | boot          | hermit
 *  0        | boot          | OS auto boot
 * -12345678-+---------------+----------------------------
 *   00      | boot device   | eMMC
 *   10      | boot device   | SDHI0 (CON7)
 *   01      | boot device   | -
 *   11      | boot device   | Extension Buss (CS0)
 * -12345678-+---------------+----------------------------
 *     0     | Extension Bus | D8-D15 disable, eMMC enable
 *     1     | Extension Bus | D8-D15 enable,  eMMC disable
 * -12345678-+---------------+----------------------------
 *      0    | SDHI1         | COM8 disable, COM14 enable
 *      1    | SDHI1         | COM8 enable,  COM14 disable
 * -12345678-+---------------+----------------------------
 *       0   | USB0          | COM20 enable,  COM24 disable
 *       1   | USB0          | COM20 disable, COM24 enable
 * -12345678-+---------------+----------------------------
 *        00 | JTAG          | SH-X2
 *        10 | JTAG          | ARM
 *        01 | JTAG          | -
 *        11 | JTAG          | Boundary Scan
 *-----------+---------------+----------------------------
 */

/*
 * FSI-WM8978
 *
 * this command is required when playback.
 *
 * # amixer set "Headphone" 50
 */

/*
 * USB function
 *
 * When you use USB Function,
 * set SW1.6 ON, and connect cable to CN24.
 *
 * USBF needs workaround on R8A7740 chip.
 * These are a little bit complex.
 * see
 *	usbhsf_power_ctrl()
 */
#define IRQ7		evt2irq(0x02e0)
#define USBCR1		IOMEM(0xe605810a)
#define USBH		0xC6700000
#define USBH_USBCTR	0x10834

struct usbhsf_private {
	struct clk *phy;
	struct clk *usb24;
	struct clk *pci;
	struct clk *func;
	struct clk *host;
	void __iomem *usbh_base;
	struct renesas_usbhs_platform_info info;
};

#define usbhsf_get_priv(pdev)				\
	container_of(renesas_usbhs_get_info(pdev),	\
		     struct usbhsf_private, info)

static int usbhsf_get_id(struct platform_device *pdev)
{
	return USBHS_GADGET;
}

static void usbhsf_power_ctrl(struct platform_device *pdev,
			      void __iomem *base, int enable)
{
	struct usbhsf_private *priv = usbhsf_get_priv(pdev);

	/*
	 * Work around for USB Function.
	 * It needs USB host clock, and settings
	 */
	if (enable) {
		/*
		 * enable all the related usb clocks
		 * for usb workaround
		 */
		clk_enable(priv->usb24);
		clk_enable(priv->pci);
		clk_enable(priv->host);
		clk_enable(priv->func);
		clk_enable(priv->phy);

		/*
		 * set USBCR1
		 *
		 * Port1 is driven by USB function,
		 * Port2 is driven by USB HOST
		 * One HOST (Port1 or Port2 is HOST)
		 * USB PLL input clock = 24MHz
		 */
		__raw_writew(0xd750, USBCR1);
		mdelay(1);

		/*
		 * start USB Host
		 */
		__raw_writel(0x0000000c, priv->usbh_base + USBH_USBCTR);
		__raw_writel(0x00000008, priv->usbh_base + USBH_USBCTR);
		mdelay(10);

		/*
		 * USB PHY Power ON
		 */
		__raw_writew(0xd770, USBCR1);
		__raw_writew(0x4000, base + 0x102); /* USBF :: SUSPMODE */

	} else {
		__raw_writel(0x0000010f, priv->usbh_base + USBH_USBCTR);
		__raw_writew(0xd7c0, USBCR1); /* GPIO */

		clk_disable(priv->phy);
		clk_disable(priv->func);	/* usb work around */
		clk_disable(priv->host);	/* usb work around */
		clk_disable(priv->pci);		/* usb work around */
		clk_disable(priv->usb24);	/* usb work around */
	}
}

static int usbhsf_get_vbus(struct platform_device *pdev)
{
	return gpio_get_value(GPIO_PORT209);
}

static irqreturn_t usbhsf_interrupt(int irq, void *data)
{
	struct platform_device *pdev = data;