aiot/efDataDiscreteRateMining/databaseOperation/analysisDataOperation.h

/*
 *	FILE    	SA-1100.h
 *
 *	Version 	1.2
 *	Author  	Copyright (c) Marc A. Viredaz, 1998
 *	        	DEC Western Research Laboratory, Palo Alto, CA
 *	Date    	January 1998 (April 1997)
 *	System  	StrongARM SA-1100
 *	Language	C or ARM Assembly
 *	Purpose 	Definition of constants related to the StrongARM
 *	        	SA-1100 microprocessor (Advanced RISC Machine (ARM)
 *	        	architecture version 4). This file is based on the
 *	        	StrongARM SA-1100 data sheet version 2.2.
 *
 */


/* Be sure that virtual mapping is defined right */
#ifndef __ASM_ARCH_HARDWARE_H
#error You must include hardware.h not SA-1100.h
#endif

#include "bitfield.h"

/*
 * SA1100 CS line to physical address
 */

#define SA1100_CS0_PHYS	0x00000000
#define SA1100_CS1_PHYS	0x08000000
#define SA1100_CS2_PHYS	0x10000000
#define SA1100_CS3_PHYS	0x18000000
#define SA1100_CS4_PHYS	0x40000000
#define SA1100_CS5_PHYS	0x48000000

/*
 * Personal Computer Memory Card International Association (PCMCIA) sockets
 */

#define PCMCIAPrtSp	0x04000000	/* PCMCIA Partition Space [byte]   */
#define PCMCIASp	(4*PCMCIAPrtSp)	/* PCMCIA Space [byte]             */
#define PCMCIAIOSp	PCMCIAPrtSp	/* PCMCIA I/O Space [byte]         */
#define PCMCIAAttrSp	PCMCIAPrtSp	/* PCMCIA Attribute Space [byte]   */
#define PCMCIAMemSp	PCMCIAPrtSp	/* PCMCIA Memory Space [byte]      */

#define PCMCIA0Sp	PCMCIASp	/* PCMCIA 0 Space [byte]           */
#define PCMCIA0IOSp	PCMCIAIOSp	/* PCMCIA 0 I/O Space [byte]       */
#define PCMCIA0AttrSp	PCMCIAAttrSp	/* PCMCIA 0 Attribute Space [byte] */
#define PCMCIA0MemSp	PCMCIAMemSp	/* PCMCIA 0 Memory Space [byte]    */

#define PCMCIA1Sp	PCMCIASp	/* PCMCIA 1 Space [byte]           */
#define PCMCIA1IOSp	PCMCIAIOSp	/* PCMCIA 1 I/O Space [byte]       */
#define PCMCIA1AttrSp	PCMCIAAttrSp	/* PCMCIA 1 Attribute Space [byte] */
#define PCMCIA1MemSp	PCMCIAMemSp	/* PCMCIA 1 Memory Space [byte]    */

#define _PCMCIA(Nb)	        	/* PCMCIA [0..1]                   */ \
                	(0x20000000 + (Nb)*PCMCIASp)
#define _PCMCIAIO(Nb)	_PCMCIA (Nb)	/* PCMCIA I/O [0..1]               */
#define _PCMCIAAttr(Nb)	        	/* PCMCIA Attribute [0..1]         */ \
                	(_PCMCIA (Nb) + 2*PCMCIAPrtSp)
#define _PCMCIAMem(Nb)	        	/* PCMCIA Memory [0..1]            */ \
                	(_PCMCIA (Nb) + 3*PCMCIAPrtSp)

#define _PCMCIA0	_PCMCIA (0)	/* PCMCIA 0                        */
#define _PCMCIA0IO	_PCMCIAIO (0)	/* PCMCIA 0 I/O                    */
#define _PCMCIA0Attr	_PCMCIAAttr (0)	/* PCMCIA 0 Attribute              */
#define _PCMCIA0Mem	_PCMCIAMem (0)	/* PCMCIA 0 Memory                 */

#define _PCMCIA1	_PCMCIA (1)	/* PCMCIA 1                        */
#define _PCMCIA1IO	_PCMCIAIO (1)	/* PCMCIA 1 I/O                    */
#define _PCMCIA1Attr	_PCMCIAAttr (1)	/* PCMCIA 1 Attribute              */
#define _PCMCIA1Mem	_PCMCIAMem (1)	/* PCMCIA 1 Memory                 */


/*
 * Universal Serial Bus (USB) Device Controller (UDC) control registers
 *
 * Registers
 *    Ser0UDCCR 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Control Register (read/write).
 *    Ser0UDCAR 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Address Register (read/write).
 *    Ser0UDCOMP	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Output Maximum Packet size register
 *              	(read/write).
 *    Ser0UDCIMP	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Input Maximum Packet size register
 *              	(read/write).
 *    Ser0UDCCS0	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Control/Status register end-point 0
 *              	(read/write).
 *    Ser0UDCCS1	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Control/Status register end-point 1
 *              	(output, read/write).
 *    Ser0UDCCS2	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Control/Status register end-point 2
 *              	(input, read/write).
 *    Ser0UDCD0 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Data register end-point 0
 *              	(read/write).
 *    Ser0UDCWC 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Write Count register end-point 0
 *              	(read).
 *    Ser0UDCDR 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Data Register (read/write).
 *    Ser0UDCSR 	Serial port 0 Universal Serial Bus (USB) Device
 *              	Controller (UDC) Status Register (read/write).
 */

#define Ser0UDCCR	__REG(0x80000000)  /* Ser. port 0 UDC Control Reg. */
#define Ser0UDCAR	__REG(0x80000004)  /* Ser. port 0 UDC Address Reg. */
#define Ser0UDCOMP	__REG(0x80000008)  /* Ser. port 0 UDC Output Maximum Packet size reg. */
#define Ser0UDCIMP	__REG(0x8000000C)  /* Ser. port 0 UDC Input Maximum Packet size reg. */
#define Ser0UDCCS0	__REG(0x80000010)  /* Ser. port 0 UDC Control/Status reg. end-point 0 */
#define Ser0UDCCS1	__REG(0x80000014)  /* Ser. port 0 UDC Control/Status reg. end-point 1 (output) */
#define Ser0UDCCS2	__REG(0x80000018)  /* Ser. port 0 UDC Control/Status reg. end-point 2 (input) */
#define Ser0UDCD0	__REG(0x8000001C)  /* Ser. port 0 UDC Data reg. end-point 0 */
#define Ser0UDCWC	__REG(0x80000020)  /* Ser. port 0 UDC Write Count reg. end-point 0 */
#define Ser0UDCDR	__REG(0x80000028)  /* Ser. port 0 UDC Data Reg. */
#define Ser0UDCSR	__REG(0x80000030)  /* Ser. port 0 UDC Status Reg. */

#define UDCCR_UDD	0x00000001	/* UDC Disable                     */
#define UDCCR_UDA	0x00000002	/* UDC Active (read)               */
#define UDCCR_RESIM	0x00000004	/* Resume Interrupt Mask, per errata */
#define UDCCR_EIM	0x00000008	/* End-point 0 Interrupt Mask      */
                	        	/* (disable)                       */
#define UDCCR_RIM	0x00000010	/* Receive Interrupt Mask          */
                	        	/* (disable)                       */
#define UDCCR_TIM	0x00000020	/* Transmit Interrupt Mask         */
                	        	/* (disable)                       */
#define UDCCR_SRM	0x00000040	/* Suspend/Resume interrupt Mask   */
                	        	/* (disable)                       */
#define UDCCR_SUSIM	UDCCR_SRM	/* Per errata, SRM just masks suspend */
#define UDCCR_REM	0x00000080	/* REset interrupt Mask (disable)  */

#define UDCAR_ADD	Fld (7, 0)	/* function ADDress                */

#define UDCOMP_OUTMAXP	Fld (8, 0)	/* OUTput MAXimum Packet size - 1  */
                	        	/* [byte]                          */
#define UDCOMP_OutMaxPkt(Size)  	/* Output Maximum Packet size      */ \
                	        	/* [1..256 byte]                   */ \
                	(((Size) - 1) << FShft (UDCOMP_OUTMAXP))

#define UDCIMP_INMAXP	Fld (8, 0)	/* INput MAXimum Packet size - 1   */
                	        	/* [byte]                          */
#define UDCIMP_InMaxPkt(Size)   	/* Input Maximum Packet size       */ \
                	        	/* [1..256 byte]                   */ \
                	(((Size) - 1) << FShft (UDCIMP_INMAXP))

#define UDCCS0_OPR	0x00000001	/* Output Packet Ready (read)      */
#define UDCCS0_IPR	0x00000002	/* Input Packet Ready              */
#define UDCCS0_SST	0x00000004	/* Sent STall                      */
#define UDCCS0_FST	0x00000008	/* Force STall                     */
#define UDCCS0_DE	0x00000010	/* Data End                        */
#define UDCCS0_SE	0x00000020	/* Setup End (read)                */
#define UDCCS0_SO	0x00000040	/* Serviced Output packet ready    */
                	        	/* (write)                         */
#define UDCCS0_SSE	0x00000080	/* Serviced Setup End (write)      */

#define UDCCS1_RFS	0x00000001	/* Receive FIFO 12-bytes or more   */
                	        	/* Service request (read)          */
#define UDCCS1_RPC	0x00000002	/* Receive Packet Complete         */
#define UDCCS1_RPE	0x00000004	/* Receive Packet Error (read)     */
#define UDCCS1_SST	0x00000008	/* Sent STall                      */
#define UDCCS1_FST	0x00000010	/* Force STall                     */
#define UDCCS1_RNE	0x00000020	/* Receive FIFO Not Empty (read)   */

#define UDCCS2_TFS	0x00000001	/* Transmit FIFO 8-bytes or less   */
                	        	/* Service request (read)          */
#define UDCCS2_TPC	0x00000002	/* Transmit Packet Complete        */
#define UDCCS2_TPE	0x00000004	/* Transmit Packet Error (read)    */
#define UDCCS2_TUR	0x00000008	/* Transmit FIFO Under-Run         */
#define UDCCS2_SST	0x00000010	/* Sent STall                      */
#define UDCCS2_FST	0x00000020	/* Force STall                     */

#define UDCD0_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */

#define UDCWC_WC	Fld (4, 0)	/* Write Count                     */

#define UDCDR_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */

#define UDCSR_EIR	0x00000001	/* End-point 0 Interrupt Request   */
#define UDCSR_RIR	0x00000002	/* Receive Interrupt Request       */
#define UDCSR_TIR	0x00000004	/* Transmit Interrupt Request      */
#define UDCSR_SUSIR	0x00000008	/* SUSpend Interrupt Request       */
#define UDCSR_RESIR	0x00000010	/* RESume Interrupt Request        */
#define UDCSR_RSTIR	0x00000020	/* ReSeT Interrupt Request         */


/*
 * Universal Asynchronous Receiver/Transmitter (UART) control registers
 *
 * Registers
 *    Ser1UTCR0 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 0
 *              	(read/write).
 *    Ser1UTCR1 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 1
 *              	(read/write).
 *    Ser1UTCR2 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 2
 *              	(read/write).
 *    Ser1UTCR3 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 3
 *              	(read/write).
 *    Ser1UTDR  	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Data Register
 *              	(read/write).
 *    Ser1UTSR0 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 0
 *              	(read/write).
 *    Ser1UTSR1 	Serial port 1 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 1 (read).
 *
 *    Ser2UTCR0 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 0
 *              	(read/write).
 *    Ser2UTCR1 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 1
 *              	(read/write).
 *    Ser2UTCR2 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 2
 *              	(read/write).
 *    Ser2UTCR3 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 3
 *              	(read/write).
 *    Ser2UTCR4 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 4
 *              	(read/write).
 *    Ser2UTDR  	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Data Register
 *              	(read/write).
 *    Ser2UTSR0 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 0
 *              	(read/write).
 *    Ser2UTSR1 	Serial port 2 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 1 (read).
 *
 *    Ser3UTCR0 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 0
 *              	(read/write).
 *    Ser3UTCR1 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 1
 *              	(read/write).
 *    Ser3UTCR2 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 2
 *              	(read/write).
 *    Ser3UTCR3 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Control Register 3
 *              	(read/write).
 *    Ser3UTDR  	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Data Register
 *              	(read/write).
 *    Ser3UTSR0 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 0
 *              	(read/write).
 *    Ser3UTSR1 	Serial port 3 Universal Asynchronous
 *              	Receiver/Transmitter (UART) Status Register 1 (read).
 *
 * Clocks
 *    fxtl, Txtl	Frequency, period of the system crystal (3.6864 MHz
 *              	or 3.5795 MHz).
 *    fua, Tua  	Frequency, period of the UART communication.
 */

#define _UTCR0(Nb)	__REG(0x80010000 + ((Nb) - 1)*0x00020000)  /* UART Control Reg. 0 [1..3] */
#define _UTCR1(Nb)	__REG(0x80010004 + ((Nb) - 1)*0x00020000)  /* UART Control Reg. 1 [1..3] */
#define _UTCR2(Nb)	__REG(0x80010008 + ((Nb) - 1)*0x00020000)  /* UART Control Reg. 2 [1..3] */
#define _UTCR3(Nb)	__REG(0x8001000C + ((Nb) - 1)*0x00020000)  /* UART Control Reg. 3 [1..3] */
#define _UTCR4(Nb)	__REG(0x80010010 + ((Nb) - 1)*0x00020000)  /* UART Control Reg. 4 [2] */
#define _UTDR(Nb)	__REG(0x80010014 + ((Nb) - 1)*0x00020000)  /* UART Data Reg. [1..3] */
#define _UTSR0(Nb)	__REG(0x8001001C + ((Nb) - 1)*0x00020000)  /* UART Status Reg. 0 [1..3] */
#define _UTSR1(Nb)	__REG(0x80010020 + ((Nb) - 1)*0x00020000)  /* UART Status Reg. 1 [1..3] */

#define Ser1UTCR0	_UTCR0 (1)	/* Ser. port 1 UART Control Reg. 0 */
#define Ser1UTCR1	_UTCR1 (1)	/* Ser. port 1 UART Control Reg. 1 */
#define Ser1UTCR2	_UTCR2 (1)	/* Ser. port 1 UART Control Reg. 2 */
#define Ser1UTCR3	_UTCR3 (1)	/* Ser. port 1 UART Control Reg. 3 */
#define Ser1UTDR	_UTDR (1)	/* Ser. port 1 UART Data Reg.      */
#define Ser1UTSR0	_UTSR0 (1)	/* Ser. port 1 UART Status Reg. 0  */
#define Ser1UTSR1	_UTSR1 (1)	/* Ser. port 1 UART Status Reg. 1  */

#define Ser2UTCR0	_UTCR0 (2)	/* Ser. port 2 UART Control Reg. 0 */
#define Ser2UTCR1	_UTCR1 (2)	/* Ser. port 2 UART Control Reg. 1 */
#define Ser2UTCR2	_UTCR2 (2)	/* Ser. port 2 UART Control Reg. 2 */
#define Ser2UTCR3	_UTCR3 (2)	/* Ser. port 2 UART Control Reg. 3 */
#define Ser2UTCR4	_UTCR4 (2)	/* Ser. port 2 UART Control Reg. 4 */
#define Ser2UTDR	_UTDR (2)	/* Ser. port 2 UART Data Reg.      */
#define Ser2UTSR0	_UTSR0 (2)	/* Ser. port 2 UART Status Reg. 0  */
#define Ser2UTSR1	_UTSR1 (2)	/* Ser. port 2 UART Status Reg. 1  */

#define Ser3UTCR0	_UTCR0 (3)	/* Ser. port 3 UART Control Reg. 0 */
#define Ser3UTCR1	_UTCR1 (3)	/* Ser. port 3 UART Control Reg. 1 */
#define Ser3UTCR2	_UTCR2 (3)	/* Ser. port 3 UART Control Reg. 2 */
#define Ser3UTCR3	_UTCR3 (3)	/* Ser. port 3 UART Control Reg. 3 */
#define Ser3UTDR	_UTDR (3)	/* Ser. port 3 UART Data Reg.      */
#define Ser3UTSR0	_UTSR0 (3)	/* Ser. port 3 UART Status Reg. 0  */
#define Ser3UTSR1	_UTSR1 (3)	/* Ser. port 3 UART Status Reg. 1  */

/* Those are still used in some places */
#define _Ser1UTCR0	__PREG(Ser1UTCR0)
#define _Ser2UTCR0	__PREG(Ser2UTCR0)
#define _Ser3UTCR0	__PREG(Ser3UTCR0)

/* Register offsets */
#define UTCR0		0x00
#define UTCR1		0x04
#define UTCR2		0x08
#define UTCR3		0x0c
#define UTDR		0x14
#define UTSR0		0x1c
#define UTSR1		0x20

#define UTCR0_PE	0x00000001	/* Parity Enable                   */
#define UTCR0_OES	0x00000002	/* Odd/Even parity Select          */
#define UTCR0_OddPar	(UTCR0_OES*0)	/*  Odd Parity                     */
#define UTCR0_EvenPar	(UTCR0_OES*1)	/*  Even Parity                    */
#define UTCR0_SBS	0x00000004	/* Stop Bit Select                 */
#define UTCR0_1StpBit	(UTCR0_SBS*0)	/*  1 Stop Bit per frame           */
#define UTCR0_2StpBit	(UTCR0_SBS*1)	/*  2 Stop Bits per frame          */
#define UTCR0_DSS	0x00000008	/* Data Size Select                */
#define UTCR0_7BitData	(UTCR0_DSS*0)	/*  7-Bit Data                     */
#define UTCR0_8BitData	(UTCR0_DSS*1)	/*  8-Bit Data                     */
#define UTCR0_SCE	0x00000010	/* Sample Clock Enable             */
                	        	/* (ser. port 1: GPIO [18],        */
                	        	/* ser. port 3: GPIO [20])         */
#define UTCR0_RCE	0x00000020	/* Receive Clock Edge select       */
#define UTCR0_RcRsEdg	(UTCR0_RCE*0)	/*  Receive clock Rising-Edge      */
#define UTCR0_RcFlEdg	(UTCR0_RCE*1)	/*  Receive clock Falling-Edge     */
#define UTCR0_TCE	0x00000040	/* Transmit Clock Edge select      */
#define UTCR0_TrRsEdg	(UTCR0_TCE*0)	/*  Transmit clock Rising-Edge     */
#define UTCR0_TrFlEdg	(UTCR0_TCE*1)	/*  Transmit clock Falling-Edge    */
#define UTCR0_Ser2IrDA	        	/* Ser. port 2 IrDA settings       */ \
                	(UTCR0_1StpBit + UTCR0_8BitData)

#define UTCR1_BRD	Fld (4, 0)	/* Baud Rate Divisor/16 - 1 [11:8] */
#define UTCR2_BRD	Fld (8, 0)	/* Baud Rate Divisor/16 - 1  [7:0] */
                	        	/* fua = fxtl/(16*(BRD[11:0] + 1)) */
                	        	/* Tua = 16*(BRD [11:0] + 1)*Txtl  */
#define UTCR1_BdRtDiv(Div)      	/*  Baud Rate Divisor [16..65536]  */ \
                	(((Div) - 16)/16 >> FSize (UTCR2_BRD) << \
                	 FShft (UTCR1_BRD))
#define UTCR2_BdRtDiv(Div)      	/*  Baud Rate Divisor [16..65536]  */ \
                	(((Div) - 16)/16 & FAlnMsk (UTCR2_BRD) << \
                	 FShft (UTCR2_BRD))
                	        	/*  fua = fxtl/(16*Floor (Div/16)) */
                	        	/*  Tua = 16*Floor (Div/16)*Txtl   */
#define UTCR1_CeilBdRtDiv(Div)  	/*  Ceil. of BdRtDiv [16..65536]   */ \
                	(((Div) - 1)/16 >> FSize (UTCR2_BRD) << \
                	 FShft (UTCR1_BRD))
#define UTCR2_CeilBdRtDiv(Div)  	/*  Ceil. of BdRtDiv [16..65536]   */ \
                	(((Div) - 1)/16 & FAlnMsk (UTCR2_BRD) << \
                	 FShft (UTCR2_BRD))
                	        	/*  fua = fxtl/(16*Ceil (Div/16))  */
                	        	/*  Tua = 16*Ceil (Div/16)*Txtl    */

#define UTCR3_RXE	0x00000001	/* Receive Enable                  */
#define UTCR3_TXE	0x00000002	/* Transmit Enable                 */
#define UTCR3_BRK	0x00000004	/* BReaK mode                      */
#define UTCR3_RIE	0x00000008	/* Receive FIFO 1/3-to-2/3-full or */
                	        	/* more Interrupt Enable           */
#define UTCR3_TIE	0x00000010	/* Transmit FIFO 1/2-full or less  */
                	        	/* Interrupt Enable                */
#define UTCR3_LBM	0x00000020	/* Look-Back Mode                  */
#define UTCR3_Ser2IrDA	        	/* Ser. port 2 IrDA settings (RIE, */ \
                	        	/* TIE, LBM can be set or cleared) */ \
                	(UTCR3_RXE + UTCR3_TXE)

#define UTCR4_HSE	0x00000001	/* Hewlett-Packard Serial InfraRed */
                	        	/* (HP-SIR) modulation Enable      */
#define UTCR4_NRZ	(UTCR4_HSE*0)	/*  Non-Return to Zero modulation  */
#define UTCR4_HPSIR	(UTCR4_HSE*1)	/*  HP-SIR modulation              */
#define UTCR4_LPM	0x00000002	/* Low-Power Mode                  */
#define UTCR4_Z3_16Bit	(UTCR4_LPM*0)	/*  Zero pulse = 3/16 Bit time     */
#define UTCR4_Z1_6us	(UTCR4_LPM*1)	/*  Zero pulse = 1.6 us            */

#define UTDR_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */
#if 0           	        	/* Hidden receive FIFO bits        */
#define UTDR_PRE	0x00000100	/*  receive PaRity Error (read)    */
#define UTDR_FRE	0x00000200	/*  receive FRaming Error (read)   */
#define UTDR_ROR	0x00000400	/*  Receive FIFO Over-Run (read)   */
#endif /* 0 */

#define UTSR0_TFS	0x00000001	/* Transmit FIFO 1/2-full or less  */
                	        	/* Service request (read)          */
#define UTSR0_RFS	0x00000002	/* Receive FIFO 1/3-to-2/3-full or */
                	        	/* more Service request (read)     */
#define UTSR0_RID	0x00000004	/* Receiver IDle                   */
#define UTSR0_RBB	0x00000008	/* Receive Beginning of Break      */
#define UTSR0_REB	0x00000010	/* Receive End of Break            */
#define UTSR0_EIF	0x00000020	/* Error In FIFO (read)            */

#define UTSR1_TBY	0x00000001	/* Transmitter BusY (read)         */
#define UTSR1_RNE	0x00000002	/* Receive FIFO Not Empty (read)   */
#define UTSR1_TNF	0x00000004	/* Transmit FIFO Not Full (read)   */
#define UTSR1_PRE	0x00000008	/* receive PaRity Error (read)     */
#define UTSR1_FRE	0x00000010	/* receive FRaming Error (read)    */
#define UTSR1_ROR	0x00000020	/* Receive FIFO Over-Run (read)    */


/*
 * Synchronous Data Link Controller (SDLC) control registers
 *
 * Registers
 *    Ser1SDCR0 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Control Register 0 (read/write).
 *    Ser1SDCR1 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Control Register 1 (read/write).
 *    Ser1SDCR2 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Control Register 2 (read/write).
 *    Ser1SDCR3 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Control Register 3 (read/write).
 *    Ser1SDCR4 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Control Register 4 (read/write).
 *    Ser1SDDR  	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Data Register (read/write).
 *    Ser1SDSR0 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Status Register 0 (read/write).
 *    Ser1SDSR1 	Serial port 1 Synchronous Data Link Controller (SDLC)
 *              	Status Register 1 (read/write).
 *
 * Clocks
 *    fxtl, Txtl	Frequency, period of the system crystal (3.6864 MHz
 *              	or 3.5795 MHz).
 *    fsd, Tsd  	Frequency, period of the SDLC communication.
 */

#define Ser1SDCR0	__REG(0x80020060)  /* Ser. port 1 SDLC Control Reg. 0 */
#define Ser1SDCR1	__REG(0x80020064)  /* Ser. port 1 SDLC Control Reg. 1 */
#define Ser1SDCR2	__REG(0x80020068)  /* Ser. port 1 SDLC Control Reg. 2 */
#define Ser1SDCR3	__REG(0x8002006C)  /* Ser. port 1 SDLC Control Reg. 3 */
#define Ser1SDCR4	__REG(0x80020070)  /* Ser. port 1 SDLC Control Reg. 4 */
#define Ser1SDDR	__REG(0x80020078)  /* Ser. port 1 SDLC Data Reg.      */
#define Ser1SDSR0	__REG(0x80020080)  /* Ser. port 1 SDLC Status Reg. 0  */
#define Ser1SDSR1	__REG(0x80020084)  /* Ser. port 1 SDLC Status Reg. 1  */

#define SDCR0_SUS	0x00000001	/* SDLC/UART Select                */
#define SDCR0_SDLC	(SDCR0_SUS*0)	/*  SDLC mode (TXD1 & RXD1)        */
#define SDCR0_UART	(SDCR0_SUS*1)	/*  UART mode (TXD1 & RXD1)        */
#define SDCR0_SDF	0x00000002	/* Single/Double start Flag select */
#define SDCR0_SglFlg	(SDCR0_SDF*0)	/*  Single start Flag              */
#define SDCR0_DblFlg	(SDCR0_SDF*1)	/*  Double start Flag              */
#define SDCR0_LBM	0x00000004	/* Look-Back Mode                  */
#define SDCR0_BMS	0x00000008	/* Bit Modulation Select           */
#define SDCR0_FM0	(SDCR0_BMS*0)	/*  Freq. Modulation zero (0)      */
#define SDCR0_NRZ	(SDCR0_BMS*1)	/*  Non-Return to Zero modulation  */
#define SDCR0_SCE	0x00000010	/* Sample Clock Enable (GPIO [16]) */
#define SDCR0_SCD	0x00000020	/* Sample Clock Direction select   */
                	        	/* (GPIO [16])                     */
#define SDCR0_SClkIn	(SDCR0_SCD*0)	/*  Sample Clock Input             */
#define SDCR0_SClkOut	(SDCR0_SCD*1)	/*  Sample Clock Output            */
#define SDCR0_RCE	0x00000040	/* Receive Clock Edge select       */
#define SDCR0_RcRsEdg	(SDCR0_RCE*0)	/*  Receive clock Rising-Edge      */
#define SDCR0_RcFlEdg	(SDCR0_RCE*1)	/*  Receive clock Falling-Edge     */
#define SDCR0_TCE	0x00000080	/* Transmit Clock Edge select      */
#define SDCR0_TrRsEdg	(SDCR0_TCE*0)	/*  Transmit clock Rising-Edge     */
#define SDCR0_TrFlEdg	(SDCR0_TCE*1)	/*  Transmit clock Falling-Edge    */

#define SDCR1_AAF	0x00000001	/* Abort After Frame enable        */
                	        	/* (GPIO [17])                     */
#define SDCR1_TXE	0x00000002	/* Transmit Enable                 */
#define SDCR1_RXE	0x00000004	/* Receive Enable                  */
#define SDCR1_RIE	0x00000008	/* Receive FIFO 1/3-to-2/3-full or */
                	        	/* more Interrupt Enable           */
#define SDCR1_TIE	0x00000010	/* Transmit FIFO 1/2-full or less  */
                	        	/* Interrupt Enable                */
#define SDCR1_AME	0x00000020	/* Address Match Enable            */
#define SDCR1_TUS	0x00000040	/* Transmit FIFO Under-run Select  */
#define SDCR1_EFrmURn	(SDCR1_TUS*0)	/*  End Frame on Under-Run         */
#define SDCR1_AbortURn	(SDCR1_TUS*1)	/*  Abort on Under-Run             */
#define SDCR1_RAE	0x00000080	/* Receive Abort interrupt Enable  */

#define SDCR2_AMV	Fld (8, 0)	/* Address Match Value             */

#define SDCR3_BRD	Fld (4, 0)	/* Baud Rate Divisor/16 - 1 [11:8] */
#define SDCR4_BRD	Fld (8, 0)	/* Baud Rate Divisor/16 - 1  [7:0] */
                	        	/* fsd = fxtl/(16*(BRD[11:0] + 1)) */
                	        	/* Tsd = 16*(BRD[11:0] + 1)*Txtl   */
#define SDCR3_BdRtDiv(Div)      	/*  Baud Rate Divisor [16..65536]  */ \
                	(((Div) - 16)/16 >> FSize (SDCR4_BRD) << \
                	 FShft (SDCR3_BRD))
#define SDCR4_BdRtDiv(Div)      	/*  Baud Rate Divisor [16..65536]  */ \
                	(((Div) - 16)/16 & FAlnMsk (SDCR4_BRD) << \
                	 FShft (SDCR4_BRD))
                	        	/*  fsd = fxtl/(16*Floor (Div/16)) */
                	        	/*  Tsd = 16*Floor (Div/16)*Txtl   */
#define SDCR3_CeilBdRtDiv(Div)  	/*  Ceil. of BdRtDiv [16..65536]   */ \
                	(((Div) - 1)/16 >> FSize (SDCR4_BRD) << \
                	 FShft (SDCR3_BRD))
#define SDCR4_CeilBdRtDiv(Div)  	/*  Ceil. of BdRtDiv [16..65536]   */ \
                	(((Div) - 1)/16 & FAlnMsk (SDCR4_BRD) << \
                	 FShft (SDCR4_BRD))
                	        	/*  fsd = fxtl/(16*Ceil (Div/16))  */
                	        	/*  Tsd = 16*Ceil (Div/16)*Txtl    */

#define SDDR_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */
#if 0           	        	/* Hidden receive FIFO bits        */
#define SDDR_EOF	0x00000100	/*  receive End-Of-Frame (read)    */
#define SDDR_CRE	0x00000200	/*  receive CRC Error (read)       */
#define SDDR_ROR	0x00000400	/*  Receive FIFO Over-Run (read)   */
#endif /* 0 */

#define SDSR0_EIF	0x00000001	/* Error In FIFO (read)            */
#define SDSR0_TUR	0x00000002	/* Transmit FIFO Under-Run         */
#define SDSR0_RAB	0x00000004	/* Receive ABort                   */
#define SDSR0_TFS	0x00000008	/* Transmit FIFO 1/2-full or less  */
                	        	/* Service request (read)          */
#define SDSR0_RFS	0x00000010	/* Receive FIFO 1/3-to-2/3-full or */
                	        	/* more Service request (read)     */

#define SDSR1_RSY	0x00000001	/* Receiver SYnchronized (read)    */
#define SDSR1_TBY	0x00000002	/* Transmitter BusY (read)         */
#define SDSR1_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */
#define SDSR1_TNF	0x00000008	/* Transmit FIFO Not Full (read)   */
#define SDSR1_RTD	0x00000010	/* Receive Transition Detected     */
#define SDSR1_EOF	0x00000020	/* receive End-Of-Frame (read)     */
#define SDSR1_CRE	0x00000040	/* receive CRC Error (read)        */
#define SDSR1_ROR	0x00000080	/* Receive FIFO Over-Run (read)    */


/*
 * High-Speed Serial to Parallel controller (HSSP) control registers
 *
 * Registers
 *    Ser2HSCR0 	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Control Register 0 (read/write).
 *    Ser2HSCR1 	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Control Register 1 (read/write).
 *    Ser2HSDR  	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Data Register (read/write).
 *    Ser2HSSR0 	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Status Register 0 (read/write).
 *    Ser2HSSR1 	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Status Register 1 (read).
 *    Ser2HSCR2 	Serial port 2 High-Speed Serial to Parallel
 *              	controller (HSSP) Control Register 2 (read/write).
 *              	[The HSCR2 register is only implemented in
 *              	versions 2.0 (rev. = 8) and higher of the StrongARM
 *              	SA-1100.]
 */

#define Ser2HSCR0	__REG(0x80040060)  /* Ser. port 2 HSSP Control Reg. 0 */
#define Ser2HSCR1	__REG(0x80040064)  /* Ser. port 2 HSSP Control Reg. 1 */
#define Ser2HSDR	__REG(0x8004006C)  /* Ser. port 2 HSSP Data Reg.      */
#define Ser2HSSR0	__REG(0x80040074)  /* Ser. port 2 HSSP Status Reg. 0  */
#define Ser2HSSR1	__REG(0x80040078)  /* Ser. port 2 HSSP Status Reg. 1  */
#define Ser2HSCR2	__REG(0x90060028)  /* Ser. port 2 HSSP Control Reg. 2 */

#define HSCR0_ITR	0x00000001	/* IrDA Transmission Rate          */
#define HSCR0_UART	(HSCR0_ITR*0)	/*  UART mode (115.2 kb/s if IrDA) */
#define HSCR0_HSSP	(HSCR0_ITR*1)	/*  HSSP mode (4 Mb/s)             */
#define HSCR0_LBM	0x00000002	/* Look-Back Mode                  */
#define HSCR0_TUS	0x00000004	/* Transmit FIFO Under-run Select  */
#define HSCR0_EFrmURn	(HSCR0_TUS*0)	/*  End Frame on Under-Run         */
#define HSCR0_AbortURn	(HSCR0_TUS*1)	/*  Abort on Under-Run             */
#define HSCR0_TXE	0x00000008	/* Transmit Enable                 */
#define HSCR0_RXE	0x00000010	/* Receive Enable                  */
#define HSCR0_RIE	0x00000020	/* Receive FIFO 2/5-to-3/5-full or */
                	        	/* more Interrupt Enable           */
#define HSCR0_TIE	0x00000040	/* Transmit FIFO 1/2-full or less  */
                	        	/* Interrupt Enable                */
#define HSCR0_AME	0x00000080	/* Address Match Enable            */

#define HSCR1_AMV	Fld (8, 0)	/* Address Match Value             */

#define HSDR_DATA	Fld (8, 0)	/* receive/transmit DATA FIFOs     */
#if 0           	        	/* Hidden receive FIFO bits        */
#define HSDR_EOF	0x00000100	/*  receive End-Of-Frame (read)    */
#define HSDR_CRE	0x00000200	/*  receive CRC Error (read)       */
#define HSDR_ROR	0x00000400	/*  Receive FIFO Over-Run (read)   */
#endif /* 0 */

#define HSSR0_EIF	0x00000001	/* Error In FIFO (read)            */
#define HSSR0_TUR	0x00000002	/* Transmit FIFO Under-Run         */
#define HSSR0_RAB	0x00000004	/* Receive ABort                   */
#define HSSR0_TFS	0x00000008	/* Transmit FIFO 1/2-full or less  */
                	        	/* Service request (read)          */
#define HSSR0_RFS	0x00000010	/* Receive FIFO 2/5-to-3/5-full or */
                	        	/* more Service request (read)     */
#define HSSR0_FRE	0x00000020	/* receive FRaming Error           */

#define HSSR1_RSY	0x00000001	/* Receiver SYnchronized (read)    */
#define HSSR1_TBY	0x00000002	/* Transmitter BusY (read)         */
#define HSSR1_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */
#define HSSR1_TNF	0x00000008	/* Transmit FIFO Not Full (read)   */
#define HSSR1_EOF	0x00000010	/* receive End-Of-Frame (read)     */
#define HSSR1_CRE	0x00000020	/* receive CRC Error (read)        */
#define HSSR1_ROR	0x00000040	/* Receive FIFO Over-Run (read)    */

#define HSCR2_TXP	0x00040000	/* Transmit data Polarity (TXD_2)  */
#define HSCR2_TrDataL	(HSCR2_TXP*0)	/*  Transmit Data active Low       */
                	        	/*  (inverted)                     */
#define HSCR2_TrDataH	(HSCR2_TXP*1)	/*  Transmit Data active High      */
                	        	/*  (non-inverted)                 */
#define HSCR2_RXP	0x00080000	/* Receive data Polarity (RXD_2)   */
#define HSCR2_RcDataL	(HSCR2_RXP*0)	/*  Receive Data active Low        */
                	        	/*  (inverted)                     */
#define HSCR2_RcDataH	(HSCR2_RXP*1)	/*  Receive Data active High       */
                	        	/*  (non-inverted)                 */


/*
 * Multi-media Communications Port (MCP) control registers
 *
 * Registers
 *    Ser4MCCR0 	Serial port 4 Multi-media Communications Port (MCP)
 *              	Control Register 0 (read/write).
 *    Ser4MCDR0 	Serial port 4 Multi-media Communications Port (MCP)
 *              	Data Register 0 (audio, read/write).
 *    Ser4MCDR1 	Serial port 4 Multi-media Communications Port (MCP)
 *              	Data Register 1 (telecom, read/write).
 *    Ser4MCDR2 	Serial port 4 Multi-media Communications Port (MCP)
 *              	Data Register 2 (CODEC registers, read/write).
 *    Ser4MCSR  	Serial port 4 Multi-media Communications Port (MCP)
 *              	Status Register (read/write).
 *    Ser4MCCR1 	Serial port 4 Multi-media Communications Port (MCP)
 *              	Control Register 1 (read/write).
 *              	[The MCCR1 register is only implemented in
 *              	versions 2.0 (rev. = 8) and higher of the StrongARM
 *              	SA-1100.]
 *
 * Clocks
 *    fmc, Tmc  	Frequency, period of the MCP communication (10 MHz,
 *              	12 MHz, or GPIO [21]).
 *    faud, Taud	Frequency, period of the audio sampling.
 *    ftcm, Ttcm	Frequency, period of the telecom sampling.
 */

#define Ser4MCCR0	__REG(0x80060000)  /* Ser. port 4 MCP Control Reg. 0 */
#define Ser4MCDR0	__REG(0x80060008)  /* Ser. port 4 MCP Data Reg. 0 (audio) */
#define Ser4MCDR1	__REG(0x8006000C)  /* Ser. port 4 MCP Data Reg. 1 (telecom) */
#define Ser4MCDR2	__REG(0x80060010)  /* Ser. port 4 MCP Data Reg. 2 (CODEC reg.) */
#define Ser4MCSR	__REG(0x80060018)  /* Ser. port 4 MCP Status Reg. */
#define Ser4MCCR1	__REG(0x90060030)  /* Ser. port 4 MCP Control Reg. 1 */

#define MCCR0_ASD	Fld (7, 0)	/* Audio Sampling rate Divisor/32  */
                	        	/* [6..127]                        */
                	        	/* faud = fmc/(32*ASD)             */
                	        	/* Taud = 32*ASD*Tmc               */
#define MCCR0_AudSmpDiv(Div)    	/*  Audio Sampling rate Divisor    */ \
                	        	/*  [192..4064]                    */ \
                	((Div)/32 << FShft (MCCR0_ASD))
                	        	/*  faud = fmc/(32*Floor (Div/32)) */
                	        	/*  Taud = 32*Floor (Div/32)*Tmc   */
#define MCCR0_CeilAudSmpDiv(Div)	/*  Ceil. of AudSmpDiv [192..4064] */ \
                	(((Div) + 31)/32 << FShft (MCCR0_ASD))
                	        	/*  faud = fmc/(32*Ceil (Div/32))  */
                	        	/*  Taud = 32*Ceil (Div/32)*Tmc    */
#define MCCR0_TSD	Fld (7, 8)	/* Telecom Sampling rate           */
                	        	/* Divisor/32 [16..127]            */
                	        	/* ftcm = fmc/(32*TSD)             */
                	        	/* Ttcm = 32*TSD*Tmc               */
#define MCCR0_TcmSmpDiv(Div)    	/*  Telecom Sampling rate Divisor  */ \
                	        	/*  [512..4064]                    */ \
                	((Div)/32 << FShft (MCCR0_TSD))
                	        	/*  ftcm = fmc/(32*Floor (Div/32)) */
                	        	/*  Ttcm = 32*Floor (Div/32)*Tmc   */
#define MCCR0_CeilTcmSmpDiv(Div)	/*  Ceil. of TcmSmpDiv [512..4064] */ \
                	(((Div) + 31)/32 << FShft (MCCR0_TSD))
                	        	/*  ftcm = fmc/(32*Ceil (Div/32))  */
                	        	/*  Ttcm = 32*Ceil (Div/32)*Tmc    */
#define MCCR0_MCE	0x00010000	/* MCP Enable                      */
#define MCCR0_ECS	0x00020000	/* External Clock Select           */
#define MCCR0_IntClk	(MCCR0_ECS*0)	/*  Internal Clock (10 or 12 MHz)  */
#define MCCR0_ExtClk	(MCCR0_ECS*1)	/*  External Clock (GPIO [21])     */
#define MCCR0_ADM	0x00040000	/* A/D (audio/telecom) data        */
                	        	/* sampling/storing Mode           */
#define MCCR0_VldBit	(MCCR0_ADM*0)	/*  Valid Bit storing mode         */
#define MCCR0_SmpCnt	(MCCR0_ADM*1)	/*  Sampling Counter storing mode  */
#define MCCR0_TTE	0x00080000	/* Telecom Transmit FIFO 1/2-full  */
                	        	/* or less interrupt Enable        */
#define MCCR0_TRE	0x00100000	/* Telecom Receive FIFO 1/2-full   */
                	        	/* or more interrupt Enable        */
#define MCCR0_ATE	0x00200000	/* Audio Transmit FIFO 1/2-full    */
                	        	/* or less interrupt Enable        */
#define MCCR0_ARE	0x00400000	/* Audio Receive FIFO 1/2-full or  */
                	        	/* more interrupt Enable           */
#define MCCR0_LBM	0x00800000	/* Look-Back Mode                  */
#define MCCR0_ECP	Fld (2, 24)	/* External Clock Prescaler - 1    */
#define MCCR0_ExtClkDiv(Div)    	/*  External Clock Divisor [1..4]  */ \
                	(((Div) - 1) << FShft (MCCR0_ECP))

#define MCDR0_DATA	Fld (12, 4)	/* receive/transmit audio DATA     */
                	        	/* FIFOs                           */

#define MCDR1_DATA	Fld (14, 2)	/* receive/transmit telecom DATA   */
                	        	/* FIFOs                           */

                	        	/* receive/transmit CODEC reg.     */
                	        	/* FIFOs:                          */
#define MCDR2_DATA	Fld (16, 0)	/*  reg. DATA                      */
#define MCDR2_RW	0x00010000	/*  reg. Read/Write (transmit)     */
#define MCDR2_Rd	(MCDR2_RW*0)	/*   reg. Read                     */
#define MCDR2_Wr	(MCDR2_RW*1)	/*   reg. Write                    */
#define MCDR2_ADD	Fld (4, 17)	/*  reg. ADDress                   */

#define MCSR_ATS	0x00000001	/* Audio Transmit FIFO 1/2-full    */
                	        	/* or less Service request (read)  */
#define MCSR_ARS	0x00000002	/* Audio Receive FIFO 1/2-full or  */
                	        	/* more Service request (read)     */
#define MCSR_TTS	0x00000004	/* Telecom Transmit FIFO 1/2-full  */
                	        	/* or less Service request (read)  */
#define MCSR_TRS	0x00000008	/* Telecom Receive FIFO 1/2-full   */
                	        	/* or more Service request (read)  */
#define MCSR_ATU	0x00000010	/* Audio Transmit FIFO Under-run   */
#define MCSR_ARO	0x00000020	/* Audio Receive FIFO Over-run     */
#define MCSR_TTU	0x00000040	/* Telecom Transmit FIFO Under-run */
#define MCSR_TRO	0x00000080	/* Telecom Receive FIFO Over-run   */
#define MCSR_ANF	0x00000100	/* Audio transmit FIFO Not Full    */
                	        	/* (read)                          */
#define MCSR_ANE	0x00000200	/* Audio receive FIFO Not Empty    */
                	        	/* (read)                          */
#define MCSR_TNF	0x00000400	/* Telecom transmit FIFO Not Full  */
                	        	/* (read)                          */
#define MCSR_TNE	0x00000800	/* Telecom receive FIFO Not Empty  */
                	        	/* (read)                          */
#define MCSR_CWC	0x00001000	/* CODEC register Write Completed  */
                	        	/* (read)                          */
#define MCSR_CRC	0x00002000	/* CODEC register Read Completed   */
                	        	/* (read)                          */
#define MCSR_ACE	0x00004000	/* Audio CODEC Enabled (read)      */
#define MCSR_TCE	0x00008000	/* Telecom CODEC Enabled (read)    */

#define MCCR1_CFS	0x00100000	/* Clock Freq. Select              */
#define MCCR1_F12MHz	(MCCR1_CFS*0)	/*  Freq. (fmc) = ~ 12 MHz         */
                	        	/*  (11.981 MHz)                   */
#define MCCR1_F10MHz	(MCCR1_CFS*1)	/*  Freq. (fmc) = ~ 10 MHz         */
                	        	/*  (9.585 MHz)                    */


/*
 * Synchronous Serial Port (SSP) control registers
 *
 * Registers
 *    Ser4SSCR0 	Serial port 4 Synchronous Serial Port (SSP) Control
 *              	Register 0 (read/write).
 *    Ser4SSCR1 	Serial port 4 Synchronous Serial Port (SSP) Control
 *              	Register 1 (read/write).
 *              	[Bits SPO and SP are only implemented in versions 2.0
 *              	(rev. = 8) and higher of the StrongARM SA-1100.]
 *    Ser4SSDR  	Serial port 4 Synchronous Serial Port (SSP) Data
 *              	Register (read/write).
 *    Ser4SSSR  	Serial port 4 Synchronous Serial Port (SSP) Status
 *              	Register (read/write).
 *
 * Clocks
 *    fxtl, Txtl	Frequency, period of the system crystal (3.6864 MHz
 *              	or 3.5795 MHz).
 *    fss, Tss  	Frequency, period of the SSP communication.
 */

#define Ser4SSCR0	__REG(0x80070060)  /* Ser. port 4 SSP Control Reg. 0 */
#define Ser4SSCR1	__REG(0x80070064)  /* Ser. port 4 SSP Control Reg. 1 */
#define Ser4SSDR	__REG(0x8007006C)  /* Ser. port 4 SSP Data Reg. */
#define Ser4SSSR	__REG(0x80070074)  /* Ser. port 4 SSP Status Reg. */

#define SSCR0_DSS	Fld (4, 0)	/* Data Size - 1 Select [3..15]    */
#define SSCR0_DataSize(Size)    	/*  Data Size Select [4..16]       */ \
                	(((Size) - 1) << FShft (SSCR0_DSS))
#define SSCR0_FRF	Fld (2, 4)	/* FRame Format                    */
#define SSCR0_Motorola	        	/*  Motorola Serial Peripheral     */ \
                	        	/*  Interface (SPI) format         */ \
                	(0 << FShft (SSCR0_FRF))
#define SSCR0_TI	        	/*  Texas Instruments Synchronous  */ \
                	        	/*  Serial format                  */ \
                	(1 << FShft (SSCR0_FRF))
#define SSCR0_National	        	/*  National Microwire format      */ \
                	(2 << FShft (SSCR0_FRF))
#define SSCR0_SSE	0x00000080	/* SSP Enable                      */
#define SSCR0_SCR	Fld (8, 8)	/* Serial Clock Rate divisor/2 - 1 */
                	        	/* fss = fxtl/(2*(SCR + 1))        */
                	        	/* Tss = 2*(SCR + 1)*Txtl          */
#define SSCR0_SerClkDiv(Div)    	/*  Serial Clock Divisor [2..512]  */ \
                	(((Div) - 2)/2 << FShft (SSCR0_SCR))
                	        	/*  fss = fxtl/(2*Floor (Div/2))   */
                	        	/*  Tss = 2*Floor (Div/2)*Txtl     */
#define SSCR0_CeilSerClkDiv(Div)	/*  Ceil. of SerClkDiv [2..512]    */ \
                	(((Div) - 1)/2 << FShft (SSCR0_SCR))
                	        	/*  fss = fxtl/(2*Ceil (Div/2))    */
                	        	/*  Tss = 2*Ceil (Div/2)*Txtl      */

#define SSCR1_RIE	0x00000001	/* Receive FIFO 1/2-full or more   */
                	        	/* Interrupt Enable                */
#define SSCR1_TIE	0x00000002	/* Transmit FIFO 1/2-full or less  */
                	        	/* Interrupt Enable                */
#define SSCR1_LBM	0x00000004	/* Look-Back Mode                  */
#define SSCR1_SPO	0x00000008	/* Sample clock (SCLK) POlarity    */
#define SSCR1_SClkIactL	(SSCR1_SPO*0)	/*  Sample Clock Inactive Low      */
#define SSCR1_SClkIactH	(SSCR1_SPO*1)	/*  Sample Clock Inactive High     */
#define SSCR1_SP	0x00000010	/* Sample clock (SCLK) Phase       */
#define SSCR1_SClk1P	(SSCR1_SP*0)	/*  Sample Clock active 1 Period   */
                	        	/*  after frame (SFRM, 1st edge)   */
#define SSCR1_SClk1_2P	(SSCR1_SP*1)	/*  Sample Clock active 1/2 Period */
                	        	/*  after frame (SFRM, 1st edge)   */
#define SSCR1_ECS	0x00000020	/* External Clock Select           */
#define SSCR1_IntClk	(SSCR1_ECS*0)	/*  Internal Clock                 */
#define SSCR1_ExtClk	(SSCR1_ECS*1)	/*  External Clock (GPIO [19])     */

#define SSDR_DATA	Fld (16, 0)	/* receive/transmit DATA FIFOs     */

#define SSSR_TNF	0x00000002	/* Transmit FIFO Not Full (read)   */
#define SSSR_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */
#define SSSR_BSY	0x00000008	/* SSP BuSY (read)                 */
#define SSSR_TFS	0x00000010	/* Transmit FIFO 1/2-full or less  */
                	        	/* Service request (read)          */
#define SSSR_RFS	0x00000020	/* Receive FIFO 1/2-full or more   */
                	        	/* Service request (read)          */
#define SSSR_ROR	0x00000040	/* Receive FIFO Over-Run           */


/*
 * Operating System (OS) timer control registers
 *
 * Registers
 *    OSMR0     	Operating System (OS) timer Match Register 0
 *              	(read/write).
 *    OSMR1     	Operating System (OS) timer Match Register 1
 *              	(read/write).
 *    OSMR2     	Operating System (OS) timer Match Register 2
 *              	(read/write).
 *    OSMR3     	Operating System (OS) timer Match Register 3
 *              	(read/write).
 *    OSCR      	Operating System (OS) timer Counter Register
 *              	(read/write).
 *    OSSR      	Operating System (OS) timer Status Register
 *              	(read/write).
 *    OWER      	Operating System (OS) timer Watch-dog Enable Register
 *              	(read/write).
 *    OIER      	Operating System (OS) timer Interrupt Enable Register
 *              	(read/write).
 */

#define OSMR0  		io_p2v(0x90000000)  /* OS timer Match Reg. 0 */
#define OSMR1  		io_p2v(0x90000004)  /* OS timer Match Reg. 1 */
#define OSMR2  		io_p2v(0x90000008)  /* OS timer Match Reg. 2 */
#define OSMR3  		io_p2v(0x9000000c)  /* OS timer Match Reg. 3 */
#define OSCR   		io_p2v(0x90000010)  /* OS timer Counter Reg. */
#define OSSR   		io_p2v(0x90000014)  /* OS timer Status Reg. */
#define OWER   		io_p2v(0x90000018)  /* OS timer Watch-dog Enable Reg. */
#define OIER  	 	io_p2v(0x9000001C)  /* OS timer Interrupt Enable Reg. */

#define OSSR_M(Nb)	        	/* Match detected [0..3]           */ \
                	(0x00000001 << (Nb))
#define OSSR_M0 	OSSR_M (0)	/* Match detected 0                */
#define OSSR_M1 	OSSR_M (1)	/* Match detected 1                */
#define OSSR_M2 	OSSR_M (2)	/* Match detected 2                */
#define OSSR_M3 	OSSR_M (3)	/* Match detected 3                */

#define OWER_WME	0x00000001	/* Watch-dog Match Enable          */
                	        	/* (set only)                      */

#define OIER_E(Nb)	        	/* match interrupt Enable [0..3]   */ \
                	(0x00000001 << (Nb))
#define OIER_E0 	OIER_E (0)	/* match interrupt Enable 0        */
#define OIER_E1 	OIER_E (1)	/* match interrupt Enable 1        */
#define OIER_E2 	OIER_E (2)	/* match interrupt Enable 2        */
#define OIER_E3 	OIER_E (3)	/* match interrupt Enable 3        */


/*
 * Real-Time Clock (RTC) control registers
 *
 * Registers
 *    RTAR      	Real-Time Clock (RTC) Alarm Register (read/write).
 *    RCNR      	Real-Time Clock (RTC) CouNt Register (read/write).
 *    RTTR      	Real-Time Clock (RTC) Trim Register (read/write).
 *    RTSR      	Real-Time Clock (RTC) Status Register (read/write).
 *
 * Clocks
 *    frtx, Trtx	Frequency, period of the real-time clock crystal
 *              	(32.768 kHz nominal).
 *    frtc, Trtc	Frequency, period of the real-time clock counter
 *              	(1 Hz nominal).
 */

#define RTAR		__REG(0x90010000)  /* RTC Alarm Reg. */
#define RCNR		__REG(0x90010004)  /* RTC CouNt Reg. */
#define RTTR		__REG(0x90010008)  /* RTC Trim Reg. */
#define RTSR		__REG(0x90010010)  /* RTC Status Reg. */

#define RTTR_C  	Fld (16, 0)	/* clock divider Count - 1         */
#define RTTR_D  	Fld (10, 16)	/* trim Delete count               */
                	        	/* frtc = (1023*(C + 1) - D)*frtx/ */
                	        	/*        (1023*(C + 1)^2)         */
                	        	/* Trtc = (1023*(C + 1)^2)*Trtx/   */
                	        	/*        (1023*(C + 1) - D)       */

#define RTSR_AL 	0x00000001	/* ALarm detected                  */
#define RTSR_HZ 	0x00000002	/* 1 Hz clock detected             */
#define RTSR_ALE	0x00000004	/* ALarm interrupt Enable          */
#define RTSR_HZE	0x00000008	/* 1 Hz clock interrupt Enable     */


/*
 * Power Manager (PM) control registers
 *
 * Registers
 *    PMCR      	Power Manager (PM) Control Register (read/write).
 *    PSSR      	Power Manager (PM) Sleep Status Register (read/write).
 *    PSPR      	Power Manager (PM) Scratch-Pad Register (read/write).
 *    PWER      	Power Manager (PM) Wake-up Enable Register
 *              	(read/write).
 *    PCFR      	Power Manager (PM) general ConFiguration Register
 *              	(read/write).
 *    PPCR      	Power Manager (PM) Phase-Locked Loop (PLL)
 *              	Configuration Register (read/write).
 *    PGSR      	Power Manager (PM) General-Purpose Input/Output (GPIO)
 *              	Sleep state Register (read/write, see GPIO pins).
 *    POSR      	Power Manager (PM) Oscillator Status Register (read).
 *
 * Clocks
 *    fxtl, Txtl	Frequency, period of the system crystal (3.6864 MHz
 *              	or 3.5795 MHz).
 *    fcpu, Tcpu	Frequency, period of the CPU core clock (CCLK).
 */

#define PMCR		__REG(0x90020000)  /* PM Control Reg. */
#define PSSR		__REG(0x90020004)  /* PM Sleep Status Reg. */
#define PSPR		__REG(0x90020008)  /* PM Scratch-Pad Reg. */
#define PWER		__REG(0x9002000C)  /* PM Wake-up Enable Reg. */
#define PCFR		__REG(0x90020010)  /* PM general ConFiguration Reg. */
#define PPCR		__REG(0x90020014)  /* PM PLL Configuration Reg. */
#define PGSR		__REG(0x90020018)  /* PM GPIO Sleep state Reg. */
#define POSR		__REG(0x9002001C)  /* PM Oscillator Status Reg. */

#define PMCR_SF 	0x00000001	/* Sleep Force (set only)          */

#define PSSR_SS 	0x00000001	/* Software Sleep                  */
#define PSSR_BFS	0x00000002	/* Battery Fault Status            */
                	        	/* (BATT_FAULT)                    */
#define PSSR_VFS	0x00000004	/* Vdd Fault Status (VDD_FAULT)    */
#define PSSR_DH 	0x00000008	/* DRAM control Hold               */
#define PSSR_PH 	0x00000010	/* Peripheral control Hold         */

#define PWER_GPIO(Nb)	GPIO_GPIO (Nb)	/* GPIO [0..27] wake-up enable     */
#define PWER_GPIO0	PWER_GPIO (0)	/* GPIO  [0] wake-up enable        */
#define PWER_GPIO1	PWER_GPIO (1)	/* GPIO  [1] wake-up enable        */
#define PWER_GPIO2	PWER_GPIO (2)	/* GPIO  [2] wake-up enable        */
#define PWER_GPIO3	PWER_GPIO (3)	/* GPIO  [3] wake-up enable        */
#define PWER_GPIO4	PWER_GPIO (4)	/* GPIO  [4] wake-up enable        */
#define PWER_GPIO5	PWER_GPIO (5)	/* GPIO  [5] wake-up enable        */
#define PWER_GPIO6	PWER_GPIO (6)	/* GPIO  [6] wake-up enable        */
#define PWER_GPIO7	PWER_GPIO (7)	/* GPIO  [7] wake-up enable        */
#define PWER_GPIO8	PWER_GPIO (8)	/* GPIO  [8] wake-up enable        */
#define PWER_GPIO9	PWER_GPIO (9)	/* GPIO  [9] wake-up enable        */
#define PWER_GPIO10	PWER_GPIO (10)	/* GPIO [10] wake-up enable        */
#define PWER_GPIO11	PWER_GPIO (11)	/* GPIO [11] wake-up enable        */
#define PWER_GPIO12	PWER_GPIO (12)	/* GPIO [12] wake-up enable        */
#define PWER_GPIO13	PWER_GPIO (13)	/* GPIO [13] wake-up enable        */
#define PWER_GPIO14	PWER_GPIO (14)	/* GPIO [14] wake-up enable        */
#define PWER_GPIO15	PWER_GPIO (15)	/* GPIO [15] wake-up enable        */
#define PWER_GPIO16	PWER_GPIO (16)	/* GPIO [16] wake-up enable        */
#define PWER_GPIO17	PWER_GPIO (17)	/* GPIO [17] wake-up enable        */
#define PWER_GPIO18	PWER_GPIO (18)	/* GPIO [18] wake-up enable        */
#define PWER_GPIO19	PWER_GPIO (19)	/* GPIO [19] wake-up enable        */
#define PWER_GPIO20	PWER_GPIO (20)	/* GPIO [20] wake-up enable        */
#define PWER_GPIO21	PWER_GPIO (21)	/* GPIO [21] wake-up enable        */
#define PWER_GPIO22	PWER_GPIO (22)	/* GPIO [22] wake-up enable        */
#define PWER_GPIO23	PWER_GPIO (23)	/* GPIO [23] wake-up enable        */
#define PWER_GPIO24	PWER_GPIO (24)	/* GPIO [24] wake-up enable        */
#define PWER_GPIO25	PWER_GPIO (25)	/* GPIO [25] wake-up enable        */
#define PWER_GPIO26	PWER_GPIO (26)	/* GPIO [26] wake-up enable        */
#define PWER_GPIO27	PWER_GPIO (27)	/* GPIO [27] wake-up enable        */
#define PWER_RTC	0x80000000	/* RTC alarm wake-up enable        */

#define PCFR_OPDE	0x00000001	/* Oscillator Power-Down Enable    */
#define PCFR_ClkRun	(PCFR_OPDE*0)	/*  Clock Running in sleep mode    */
#define PCFR_ClkStp	(PCFR_OPDE*1)	/*  Clock Stopped in sleep mode    */
#define PCFR_FP 	0x00000002	/* Float PCMCIA pins               */
#define PCFR_PCMCIANeg	(PCFR_FP*0)	/*  PCMCIA pins Negated (1)        */
#define PCFR_PCMCIAFlt	(PCFR_FP*1)	/*  PCMCIA pins Floating           */
#define PCFR_FS 	0x00000004	/* Float Static memory pins        */
#define PCFR_StMemNeg	(PCFR_FS*0)	/*  Static Memory pins Negated (1) */
#define PCFR_StMemFlt	(PCFR_FS*1)	/*  Static Memory pins Floating    */
#define PCFR_FO 	0x00000008	/* Force RTC oscillator            */
                	        	/* (32.768 kHz) enable On          */

#define PPCR_CCF	Fld (5, 0)	/* CPU core Clock (CCLK) Freq.     */
#define PPCR_Fx16	        	/*  Freq. x 16 (fcpu = 16*fxtl)    */ \
                	(0x00 << FShft (PPCR_CCF))
#define PPCR_Fx20	        	/*  Freq. x 20 (fcpu = 20*fxtl)    */ \
                	(0x01 << FShft (PPCR_CCF))
#define PPCR_Fx24	        	/*  Freq. x 24 (fcpu = 24*fxtl)    */ \
                	(0x02 << FShft (PPCR_CCF))
#define PPCR_Fx28	        	/*  Freq. x 28 (fcpu = 28*fxtl)    */ \
                	(0x03 << FShft (PPCR_CCF))
#define PPCR_Fx32	        	/*  Freq. x 32 (fcpu = 32*fxtl)    */ \
                	(0x04 << FShft (PPCR_CCF))
#define PPCR_Fx36	        	/*  Freq. x 36 (fcpu = 36*fxtl)    */ \
                	(0x05 << FShft (PPCR_CCF))
#define PPCR_Fx40	        	/*  Freq. x 40 (fcpu = 40*fxtl)    */ \
                	(0x06 << FShft (PPCR_CCF))
#define PPCR_Fx44	        	/*  Freq. x 44 (fcpu = 44*fxtl)    */ \
                	(0x07 << FShft (PPCR_CCF))
#define PPCR_Fx48	        	/*  Freq. x 48 (fcpu = 48*fxtl)    */ \
                	(0x08 << FShft (PPCR_CCF))
#define PPCR_Fx52	        	/*  Freq. x 52 (fcpu = 52*fxtl)    */ \
                	(0x09 << FShft (PPCR_CCF))
#define PPCR_Fx56	        	/*  Freq. x 56 (fcpu = 56*fxtl)    */ \
                	(0x0A << FShft (PPCR_CCF))
#define PPCR_Fx60	        	/*  Freq. x 60 (fcpu = 60*fxtl)    */ \
                	(0x0B << FShft (PPCR_CCF))
#define PPCR_Fx64	        	/*  Freq. x 64 (fcpu = 64*fxtl)    */ \
                	(0x0C << FShft (PPCR_CCF))
#define PPCR_Fx68	        	/*  Freq. x 68 (fcpu = 68*fxtl)    */ \
                	(0x0D << FShft (PPCR_CCF))
#define PPCR_Fx72	        	/*  Freq. x 72 (fcpu = 72*fxtl)    */ \
                	(0x0E << FShft (PPCR_CCF))
#define PPCR_Fx76	        	/*  Freq. x 76 (fcpu = 76*fxtl)    */ \
                	(0x0F << FShft (PPCR_CCF))
                	        	/*  3.6864 MHz crystal (fxtl):     */
#define PPCR_F59_0MHz	PPCR_Fx16	/*   Freq. (fcpu) =  59.0 MHz      */
#define PPCR_F73_7MHz	PPCR_Fx20	/*   Freq. (fcpu) =  73.7 MHz      */
#define PPCR_F88_5MHz	PPCR_Fx24	/*   Freq. (fcpu) =  88.5 MHz      */
#define PPCR_F103_2MHz	PPCR_Fx28	/*   Freq. (fcpu) = 103.2 MHz      */
#define PPCR_F118_0MHz	PPCR_Fx32	/*   Freq. (fcpu) = 118.0 MHz      */
#define PPCR_F132_7MHz	PPCR_Fx36	/*   Freq. (fcpu) = 132.7 MHz      */
#define PPCR_F147_5MHz	PPCR_Fx40	/*   Freq. (fcpu) = 147.5 MHz      */
#define PPCR_F162_2MHz	PPCR_Fx44	/*   Freq. (fcpu) = 162.2 MHz      */
#define PPCR_F176_9MHz	PPCR_Fx48	/*   Freq. (fcpu) = 176.9 MHz      */
#define PPCR_F191_7MHz	PPCR_Fx52	/*   Freq. (fcpu) = 191.7 MHz      */
#define PPCR_F206_4MHz	PPCR_Fx56	/*   Freq. (fcpu) = 206.4 MHz      */
#define PPCR_F221_2MHz	PPCR_Fx60	/*   Freq. (fcpu) = 221.2 MHz      */
#define PPCR_F239_6MHz	PPCR_Fx64	/*   Freq. (fcpu) = 239.6 MHz      */
#define PPCR_F250_7MHz	PPCR_Fx68	/*   Freq. (fcpu) = 250.7 MHz      */
#define PPCR_F265_4MHz	PPCR_Fx72	/*   Freq. (fcpu) = 265.4 MHz      */
#define PPCR_F280_2MHz	PPCR_Fx76	/*   Freq. (fcpu) = 280.2 MHz      */
                	        	/*  3.5795 MHz crystal (fxtl):     */
#define PPCR_F57_3MHz	PPCR_Fx16	/*   Freq. (fcpu) =  57.3 MHz      */
#define PPCR_F71_6MHz	PPCR_Fx20	/*   Freq. (fcpu) =  71.6 MHz      */
#define PPCR_F85_9MHz	PPCR_Fx24	/*   Freq. (fcpu) =  85.9 MHz      */
#define PPCR_F100_2MHz	PPCR_Fx28	/*   Freq. (fcpu) = 100.2 MHz      */
#define PPCR_F114_5MHz	PPCR_Fx32	/*   Freq. (fcpu) = 114.5 MHz      */
#define PPCR_F128_9MHz	PPCR_Fx36	/*   Freq. (fcpu) = 128.9 MHz      */
#define PPCR_F143_2MHz	PPCR_Fx40	/*   Freq. (fcpu) = 143.2 MHz      */
#define PPCR_F157_5MHz	PPCR_Fx44	/*   Freq. (fcpu) = 157.5 MHz      */
#define PPCR_F171_8MHz	PPCR_Fx48	/*   Freq. (fcpu) = 171.8 MHz      */
#define PPCR_F186_1MHz	PPCR_Fx52	/*   Freq. (fcpu) = 186.1 MHz      */
#define PPCR_F200_5MHz	PPCR_Fx56	/*   Freq. (fcpu) = 200.5 MHz      */
#define PPCR_F214_8MHz	PPCR_Fx60	/*   Freq. (fcpu) = 214.8 MHz      */
#define PPCR_F229_1MHz	PPCR_Fx64	/*   Freq. (fcpu) = 229.1 MHz      */
#define PPCR_F243_4MHz	PPCR_Fx68	/*   Freq. (fcpu) = 243.4 MHz      */
#define PPCR_F257_7MHz	PPCR_Fx72	/*   Freq. (fcpu) = 257.7 MHz      */
#define PPCR_F272_0MHz	PPCR_Fx76	/*   Freq. (fcpu) = 272.0 MHz      */

#define POSR_OOK	0x00000001	/* RTC Oscillator (32.768 kHz) OK  */


/*
 * Reset Controller (RC) control registers
 *
 * Registers
 *    RSRR      	Reset Controller (RC) Software Reset Register
 *              	(read/write).
 *    RCSR      	Reset Controller (RC) Status Register (read/write).
 */

#define RSRR		__REG(0x90030000)  /* RC Software Reset Reg. */
#define RCSR		__REG(0x90030004)  /* RC Status Reg. */

#define RSRR_SWR	0x00000001	/* SoftWare Reset (set only)       */

#define RCSR_HWR	0x00000001	/* HardWare Reset                  */
#define RCSR_SWR	0x00000002	/* SoftWare Reset                  */
#define RCSR_WDR	0x00000004	/* Watch-Dog Reset                 */
#define RCSR_SMR	0x00000008	/* Sleep-Mode Reset                */


/*
 * Test unit control registers
 *
 * Registers
 *    TUCR      	Test Unit Control Register (read/write).
 */

#define TUCR		__REG(0x90030008)  /* Test Unit Control Reg. */

#define TUCR_TIC	0x00000040	/* TIC mode                        */
#define TUCR_TTST	0x00000080	/* Trim TeST mode                  */
#define TUCR_RCRC	0x00000100	/* Richard's Cyclic Redundancy     */
                	        	/* Check                           */
#define TUCR_PMD	0x00000200	/* Power Management Disable        */
#define TUCR_MR 	0x00000400	/* Memory Request mode             */
#define TUCR_NoMB	(TUCR_MR*0)	/*  No Memory Bus request & grant  */
#define TUCR_MBGPIO	(TUCR_MR*1)	/*  Memory Bus request (MBREQ) &   */
                	        	/*  grant (MBGNT) on GPIO [22:21]  */
#define TUCR_CTB	Fld (3, 20)	/* Clock Test Bits                 */
#define TUCR_FDC	0x00800000	/* RTC Force Delete Count          */
#define TUCR_FMC	0x01000000	/* Force Michelle's Control mode   */
#define TUCR_TMC	0x02000000	/* RTC Trimmer Multiplexer Control */
#define TUCR_DPS	0x04000000	/* Disallow Pad Sleep              */
#define TUCR_TSEL	Fld (3, 29)	/* clock Test SELect on GPIO [27]  */
#define TUCR_32_768kHz	        	/*  32.768 kHz osc. on GPIO [27]   */ \
                	(0 << FShft (TUCR_TSEL))
#define TUCR_3_6864MHz	        	/*  3.6864 MHz osc. on GPIO [27]   */ \
                	(1 << FShft (TUCR_TSEL))
#define TUCR_VDD	        	/*  VDD ring osc./16 on GPIO [27]  */ \
                	(2 << FShft (TUCR_TSEL))
#define TUCR_96MHzPLL	        	/*  96 MHz PLL/4 on GPIO [27]      */ \
                	(3 << FShft (TUCR_TSEL))
#define TUCR_Clock	        	/*  internal (fcpu/2) & 32.768 kHz */ \
                	        	/*  Clocks on GPIO [26:27]         */ \
                	(4 << FShft (TUCR_TSEL))
#define TUCR_3_6864MHzA	        	/*  3.6864 MHz osc. on GPIO [27]   */ \
                	        	/*  (Alternative)                  */ \
                	(5 << FShft (TUCR_TSEL))
#define TUCR_MainPLL	        	/*  Main PLL/16 on GPIO [27]       */ \
                	(6 << FShft (TUCR_TSEL))
#define TUCR_VDDL	        	/*  VDDL ring osc./4 on GPIO [27]  */ \
                	(7 << FShft (TUCR_TSEL))


/*
 * General-Purpose Input/Output (GPIO) control registers
 *
 * Registers
 *    GPLR      	General-Purpose Input/Output (GPIO) Pin Level
 *              	Register (read).
 *    GPDR      	General-Purpose Input/Output (GPIO) Pin Direction
 *              	Register (read/write).
 *    GPSR      	General-Purpose Input/Output (GPIO) Pin output Set
 *              	Register (write).
 *    GPCR      	General-Purpose Input/Output (GPIO) Pin output Clear
 *              	Register (write).
 *    GRER      	General-Purpose Input/Output (GPIO) Rising-Edge
 *              	detect Register (read/write).
 *    GFER      	General-Purpose Input/Output (GPIO) Falling-Edge
 *              	detect Register (read/write).
 *    GEDR      	General-Purpose Input/Output (GPIO) Edge Detect
 *              	status Register (read/write).
 *    GAFR      	General-Purpose Input/Output (GPIO) Alternate
 *              	Function Register (read/write).
 *
 * Clock
 *    fcpu, Tcpu	Frequency, period of the CPU core clock (CCLK).
 */