efDataPreprocessing alarmDataOperation.c 朱俊杰 commit at 2020-11-18

efDataPreprocessing/databaseOperation/alarmDataOperation.c

@@ -453,3 +453,188 @@ void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data)
 	/* input/irq */
 	if (gpio_is_valid(data->slot[0].detect_pin)) {
 		at91_set_gpio_input(data->slot[0].detect_pin, 1);
+		at91_set_deglitch(data->slot[0].detect_pin, 1);
+	}
+	if (gpio_is_valid(data->slot[0].wp_pin))
+		at91_set_gpio_input(data->slot[0].wp_pin, 1);
+
+	if (mmc_id == 0) {		/* MCI0 */
+
+		/* CLK */
+		at91_set_A_periph(AT91_PIN_PA0, 0);
+
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA1, 1);
+
+		/* DAT0, maybe DAT1..DAT3 and maybe DAT4..DAT7 */
+		at91_set_A_periph(AT91_PIN_PA2, 1);
+		if (data->slot[0].bus_width == 4) {
+			at91_set_A_periph(AT91_PIN_PA3, 1);
+			at91_set_A_periph(AT91_PIN_PA4, 1);
+			at91_set_A_periph(AT91_PIN_PA5, 1);
+			if (data->slot[0].bus_width == 8) {
+				at91_set_A_periph(AT91_PIN_PA6, 1);
+				at91_set_A_periph(AT91_PIN_PA7, 1);
+				at91_set_A_periph(AT91_PIN_PA8, 1);
+				at91_set_A_periph(AT91_PIN_PA9, 1);
+			}
+		}
+
+		mmc0_data = *data;
+		platform_device_register(&at91sam9g45_mmc0_device);
+
+	} else {			/* MCI1 */
+
+		/* CLK */
+		at91_set_A_periph(AT91_PIN_PA31, 0);
+
+		/* CMD */
+		at91_set_A_periph(AT91_PIN_PA22, 1);
+
+		/* DAT0, maybe DAT1..DAT3 and maybe DAT4..DAT7 */
+		at91_set_A_periph(AT91_PIN_PA23, 1);
+		if (data->slot[0].bus_width == 4) {
+			at91_set_A_periph(AT91_PIN_PA24, 1);
+			at91_set_A_periph(AT91_PIN_PA25, 1);
+			at91_set_A_periph(AT91_PIN_PA26, 1);
+			if (data->slot[0].bus_width == 8) {
+				at91_set_A_periph(AT91_PIN_PA27, 1);
+				at91_set_A_periph(AT91_PIN_PA28, 1);
+				at91_set_A_periph(AT91_PIN_PA29, 1);
+				at91_set_A_periph(AT91_PIN_PA30, 1);
+			}
+		}
+
+		mmc1_data = *data;
+		platform_device_register(&at91sam9g45_mmc1_device);
+
+	}
+}
+#else
+void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  NAND / SmartMedia
+ * -------------------------------------------------------------------- */
+
+#if defined(CONFIG_MTD_NAND_ATMEL) || defined(CONFIG_MTD_NAND_ATMEL_MODULE)
+static struct atmel_nand_data nand_data;
+
+#define NAND_BASE	AT91_CHIPSELECT_3
+
+static struct resource nand_resources[] = {
+	[0] = {
+		.start	= NAND_BASE,
+		.end	= NAND_BASE + SZ_256M - 1,
+		.flags	= IORESOURCE_MEM,
+	},
+	[1] = {
+		.start	= AT91SAM9G45_BASE_ECC,
+		.end	= AT91SAM9G45_BASE_ECC + SZ_512 - 1,
+		.flags	= IORESOURCE_MEM,
+	}
+};
+
+static struct platform_device at91sam9g45_nand_device = {
+	.name		= "atmel_nand",
+	.id		= -1,
+	.dev		= {
+				.platform_data	= &nand_data,
+	},
+	.resource	= nand_resources,
+	.num_resources	= ARRAY_SIZE(nand_resources),
+};
+
+void __init at91_add_device_nand(struct atmel_nand_data *data)
+{
+	unsigned long csa;
+
+	if (!data)
+		return;
+
+	csa = at91_matrix_read(AT91_MATRIX_EBICSA);
+	at91_matrix_write(AT91_MATRIX_EBICSA, csa | AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA);
+
+	/* enable pin */
+	if (gpio_is_valid(data->enable_pin))
+		at91_set_gpio_output(data->enable_pin, 1);
+
+	/* ready/busy pin */
+	if (gpio_is_valid(data->rdy_pin))
+		at91_set_gpio_input(data->rdy_pin, 1);
+
+	/* card detect pin */
+	if (gpio_is_valid(data->det_pin))
+		at91_set_gpio_input(data->det_pin, 1);
+
+	nand_data = *data;
+	platform_device_register(&at91sam9g45_nand_device);
+}
+#else
+void __init at91_add_device_nand(struct atmel_nand_data *data) {}
+#endif
+
+
+/* --------------------------------------------------------------------
+ *  TWI (i2c)
+ * -------------------------------------------------------------------- */
+
+/*
+ * Prefer the GPIO code since the TWI controller isn't robust
+ * (gets overruns and underruns under load) and can only issue
+ * repeated STARTs in one scenario (the driver doesn't yet handle them).
+ */
+#if defined(CONFIG_I2C_GPIO) || defined(CONFIG_I2C_GPIO_MODULE)
+static struct i2c_gpio_platform_data pdata_i2c0 = {
+	.sda_pin		= AT91_PIN_PA20,
+	.sda_is_open_drain	= 1,
+	.scl_pin		= AT91_PIN_PA21,
+	.scl_is_open_drain	= 1,
+	.udelay			= 5,		/* ~100 kHz */
+};
+
+static struct platform_device at91sam9g45_twi0_device = {
+	.name			= "i2c-gpio",
+	.id			= 0,
+	.dev.platform_data	= &pdata_i2c0,
+};
+
+static struct i2c_gpio_platform_data pdata_i2c1 = {
+	.sda_pin		= AT91_PIN_PB10,
+	.sda_is_open_drain	= 1,
+	.scl_pin		= AT91_PIN_PB11,
+	.scl_is_open_drain	= 1,
+	.udelay			= 5,		/* ~100 kHz */
+};
+
+static struct platform_device at91sam9g45_twi1_device = {
+	.name			= "i2c-gpio",
+	.id			= 1,
+	.dev.platform_data	= &pdata_i2c1,
+};
+
+void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices)
+{
+	i2c_register_board_info(i2c_id, devices, nr_devices);
+
+	if (i2c_id == 0) {
+		at91_set_GPIO_periph(AT91_PIN_PA20, 1);		/* TWD (SDA) */
+		at91_set_multi_drive(AT91_PIN_PA20, 1);
+
+		at91_set_GPIO_periph(AT91_PIN_PA21, 1);		/* TWCK (SCL) */
+		at91_set_multi_drive(AT91_PIN_PA21, 1);
+
+		platform_device_register(&at91sam9g45_twi0_device);
+	} else {
+		at91_set_GPIO_periph(AT91_PIN_PB10, 1);		/* TWD (SDA) */
+		at91_set_multi_drive(AT91_PIN_PB10, 1);
+
+		at91_set_GPIO_periph(AT91_PIN_PB11, 1);		/* TWCK (SCL) */
+		at91_set_multi_drive(AT91_PIN_PB11, 1);
+
+		platform_device_register(&at91sam9g45_twi1_device);
+	}
+}
+