efDataStatistics realizationOfDataCalculation.c 张婷 commit at 2020-10-28

efDataStatistics/alarmDataCalculation/realizationOfDataCalculation.c

@@ -81,3 +81,141 @@ static struct platform_device d2net_nor_flash = {
 	.num_resources		= 1,
 	.resource		= &d2net_nor_flash_resource,
 };
+
+/*****************************************************************************
+ * Ethernet
+ ****************************************************************************/
+
+static struct mv643xx_eth_platform_data d2net_eth_data = {
+	.phy_addr	= MV643XX_ETH_PHY_ADDR(8),
+};
+
+/*****************************************************************************
+ * I2C devices
+ ****************************************************************************/
+
+/*
+ * i2c addr | chip         | description
+ * 0x32     | Ricoh 5C372b | RTC
+ * 0x3e     | GMT G762     | PWM fan controller
+ * 0x50     | HT24LC08     | eeprom (1kB)
+ *
+ * TODO: Add G762 support to the g760a driver.
+ */
+static struct i2c_board_info __initdata d2net_i2c_devices[] = {
+	{
+		I2C_BOARD_INFO("rs5c372b", 0x32),
+	}, {
+		I2C_BOARD_INFO("24c08", 0x50),
+	},
+};
+
+/*****************************************************************************
+ * SATA
+ ****************************************************************************/
+
+static struct mv_sata_platform_data d2net_sata_data = {
+	.n_ports	= 2,
+};
+
+#define D2NET_GPIO_SATA0_POWER	3
+#define D2NET_GPIO_SATA1_POWER	12
+
+static void __init d2net_sata_power_init(void)
+{
+	int err;
+
+	err = gpio_request(D2NET_GPIO_SATA0_POWER, "SATA0 power");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_SATA0_POWER, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_SATA0_POWER);
+	}
+	if (err)
+		pr_err("d2net: failed to configure SATA0 power GPIO\n");
+
+	err = gpio_request(D2NET_GPIO_SATA1_POWER, "SATA1 power");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_SATA1_POWER, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_SATA1_POWER);
+	}
+	if (err)
+		pr_err("d2net: failed to configure SATA1 power GPIO\n");
+}
+
+/*****************************************************************************
+ * GPIO LED's
+ ****************************************************************************/
+
+/*
+ * The blue front LED is wired to the CPLD and can blink in relation with the
+ * SATA activity.
+ *
+ * The following array detail the different LED registers and the combination
+ * of their possible values:
+ *
+ * led_off   | blink_ctrl | SATA active | LED state
+ *           |            |             |
+ *    1      |     x      |      x      |  off
+ *    0      |     0      |      0      |  off
+ *    0      |     1      |      0      |  blink (rate 300ms)
+ *    0      |     x      |      1      |  on
+ *
+ * Notes: The blue and the red front LED's can't be on at the same time.
+ *        Red LED have priority.
+ */
+
+#define D2NET_GPIO_RED_LED		6
+#define D2NET_GPIO_BLUE_LED_BLINK_CTRL	16
+#define D2NET_GPIO_BLUE_LED_OFF		23
+
+static struct gpio_led d2net_leds[] = {
+	{
+		.name = "d2net:blue:sata",
+		.default_trigger = "default-on",
+		.gpio = D2NET_GPIO_BLUE_LED_OFF,
+		.active_low = 1,
+	},
+	{
+		.name = "d2net:red:fail",
+		.gpio = D2NET_GPIO_RED_LED,
+	},
+};
+
+static struct gpio_led_platform_data d2net_led_data = {
+	.num_leds = ARRAY_SIZE(d2net_leds),
+	.leds = d2net_leds,
+};
+
+static struct platform_device d2net_gpio_leds = {
+	.name           = "leds-gpio",
+	.id             = -1,
+	.dev            = {
+		.platform_data  = &d2net_led_data,
+	},
+};
+
+static void __init d2net_gpio_leds_init(void)
+{
+	int err;
+
+	/* Configure GPIO over MPP max number. */
+	orion_gpio_set_valid(D2NET_GPIO_BLUE_LED_OFF, 1);
+
+	/* Configure register blink_ctrl to allow SATA activity LED blinking. */
+	err = gpio_request(D2NET_GPIO_BLUE_LED_BLINK_CTRL, "blue LED blink");
+	if (err == 0) {
+		err = gpio_direction_output(D2NET_GPIO_BLUE_LED_BLINK_CTRL, 1);
+		if (err)
+			gpio_free(D2NET_GPIO_BLUE_LED_BLINK_CTRL);
+	}
+	if (err)
+		pr_err("d2net: failed to configure blue LED blink GPIO\n");
+
+	platform_device_register(&d2net_gpio_leds);
+}
+
+/****************************************************************************
+ * GPIO keys
+ ****************************************************************************/