efDataStatistics memoryCall.c 张婷 commit at 2021-03-22

efDataStatistics/dataSharedMemory/memoryCall.c

@@ -843,3 +843,92 @@ int __init omap1_clk_init(void)
 	 */
 	{
 		unsigned pll_ctl_val = omap_readw(DPLL_CTL);
+
+		ck_dpll1.rate = ck_ref.rate; /* Base xtal rate */
+		if (pll_ctl_val & 0x10) {
+			/* PLL enabled, apply multiplier and divisor */
+			if (pll_ctl_val & 0xf80)
+				ck_dpll1.rate *= (pll_ctl_val & 0xf80) >> 7;
+			ck_dpll1.rate /= ((pll_ctl_val & 0x60) >> 5) + 1;
+		} else {
+			/* PLL disabled, apply bypass divisor */
+			switch (pll_ctl_val & 0xc) {
+			case 0:
+				break;
+			case 0x4:
+				ck_dpll1.rate /= 2;
+				break;
+			default:
+				ck_dpll1.rate /= 4;
+				break;
+			}
+		}
+	}
+	propagate_rate(&ck_dpll1);
+	/* Cache rates for clocks connected to ck_ref (not dpll1) */
+	propagate_rate(&ck_ref);
+	omap1_show_rates();
+	if (machine_is_omap_perseus2() || machine_is_omap_fsample()) {
+		/* Select slicer output as OMAP input clock */
+		omap_writew(omap_readw(OMAP7XX_PCC_UPLD_CTRL) & ~0x1,
+				OMAP7XX_PCC_UPLD_CTRL);
+	}
+
+	/* Amstrad Delta wants BCLK high when inactive */
+	if (machine_is_ams_delta())
+		omap_writel(omap_readl(ULPD_CLOCK_CTRL) |
+				(1 << SDW_MCLK_INV_BIT),
+				ULPD_CLOCK_CTRL);
+
+	/* Turn off DSP and ARM_TIMXO. Make sure ARM_INTHCK is not divided */
+	/* (on 730, bit 13 must not be cleared) */
+	if (cpu_is_omap7xx())
+		omap_writew(omap_readw(ARM_CKCTL) & 0x2fff, ARM_CKCTL);
+	else
+		omap_writew(omap_readw(ARM_CKCTL) & 0x0fff, ARM_CKCTL);
+
+	/* Put DSP/MPUI into reset until needed */
+	omap_writew(0, ARM_RSTCT1);
+	omap_writew(1, ARM_RSTCT2);
+	omap_writew(0x400, ARM_IDLECT1);
+
+	/*
+	 * According to OMAP5910 Erratum SYS_DMA_1, bit DMACK_REQ (bit 8)
+	 * of the ARM_IDLECT2 register must be set to zero. The power-on
+	 * default value of this bit is one.
+	 */
+	omap_writew(0x0000, ARM_IDLECT2);	/* Turn LCD clock off also */
+
+	/*
+	 * Only enable those clocks we will need, let the drivers
+	 * enable other clocks as necessary
+	 */
+	clk_enable(&armper_ck.clk);
+	clk_enable(&armxor_ck.clk);
+	clk_enable(&armtim_ck.clk); /* This should be done by timer code */
+
+	if (cpu_is_omap15xx())
+		clk_enable(&arm_gpio_ck);
+
+	return 0;
+}
+
+#define OMAP1_DPLL1_SANE_VALUE	60000000
+
+void __init omap1_clk_late_init(void)
+{
+	unsigned long rate = ck_dpll1.rate;
+
+	/* Find the highest supported frequency and enable it */
+	if (omap1_select_table_rate(&virtual_ck_mpu, ~0)) {
+		pr_err("System frequencies not set, using default. Check your config.\n");
+		/*
+		 * Reprogramming the DPLL is tricky, it must be done from SRAM.
+		 */
+		omap_sram_reprogram_clock(0x2290, 0x0005);
+		ck_dpll1.rate = OMAP1_DPLL1_SANE_VALUE;
+	}
+	propagate_rate(&ck_dpll1);
+	omap1_show_rates();
+	loops_per_jiffy = cpufreq_scale(loops_per_jiffy, rate, ck_dpll1.rate);
+}