waterDataDiscreteRateMining synchronousMemoryDatabase.h 吉超博 commit at 2021-03-12

waterDataDiscreteRateMining/standardDeviationCalculation/synchronousMemoryDatabase.h

@@ -138,3 +138,171 @@
 #define MCFDMA_BASE3		(MCF_MBAR + 0x3C0)	/* Base address DMA 3 */
 
 /*
+ *	Some symbol defines for the above...
+ */
+#define MCFSIM_SWDICR		MCFSIM_ICR0	/* Watchdog timer ICR */
+#define MCFSIM_TIMER1ICR	MCFSIM_ICR1	/* Timer 1 ICR */
+#define MCFSIM_TIMER2ICR	MCFSIM_ICR2	/* Timer 2 ICR */
+#define MCFSIM_I2CICR		MCFSIM_ICR3	/* I2C ICR */
+#define MCFSIM_UART1ICR		MCFSIM_ICR4	/* UART 1 ICR */
+#define MCFSIM_UART2ICR		MCFSIM_ICR5	/* UART 2 ICR */
+#define MCFSIM_DMA0ICR		MCFSIM_ICR6	/* DMA 0 ICR */
+#define MCFSIM_DMA1ICR		MCFSIM_ICR7	/* DMA 1 ICR */
+#define MCFSIM_DMA2ICR		MCFSIM_ICR8	/* DMA 2 ICR */
+#define MCFSIM_DMA3ICR		MCFSIM_ICR9	/* DMA 3 ICR */
+#define MCFSIM_QSPIICR		MCFSIM_ICR10	/* QSPI ICR */
+
+/*
+ *	Define system peripheral IRQ usage.
+ */
+#define MCF_IRQ_QSPI		28		/* QSPI, Level 4 */
+#define MCF_IRQ_I2C0		29
+#define MCF_IRQ_TIMER		30		/* Timer0, Level 6 */
+#define MCF_IRQ_PROFILER	31		/* Timer1, Level 7 */
+
+#define MCF_IRQ_UART0		73		/* UART0 */
+#define MCF_IRQ_UART1		74		/* UART1 */
+
+/*
+ * Define the base interrupt for the second interrupt controller.
+ * We set it to 128, out of the way of the base interrupts, and plenty
+ * of room for its 64 interrupts.
+ */
+#define MCFINTC2_VECBASE	128
+
+#define MCF_IRQ_GPIO0		(MCFINTC2_VECBASE + 32)
+#define MCF_IRQ_GPIO1		(MCFINTC2_VECBASE + 33)
+#define MCF_IRQ_GPIO2		(MCFINTC2_VECBASE + 34)
+#define MCF_IRQ_GPIO3		(MCFINTC2_VECBASE + 35)
+#define MCF_IRQ_GPIO4		(MCFINTC2_VECBASE + 36)
+#define MCF_IRQ_GPIO5		(MCFINTC2_VECBASE + 37)
+#define MCF_IRQ_GPIO6		(MCFINTC2_VECBASE + 38)
+#define MCF_IRQ_GPIO7		(MCFINTC2_VECBASE + 39)
+
+#define MCF_IRQ_USBWUP		(MCFINTC2_VECBASE + 40)
+#define MCF_IRQ_I2C1		(MCFINTC2_VECBASE + 62)
+
+/*
+ *	General purpose IO registers (in MBAR2).
+ */
+#define MCFSIM2_GPIOREAD	(MCF_MBAR2 + 0x000)	/* GPIO read values */
+#define MCFSIM2_GPIOWRITE	(MCF_MBAR2 + 0x004)	/* GPIO write values */
+#define MCFSIM2_GPIOENABLE	(MCF_MBAR2 + 0x008)	/* GPIO enabled */
+#define MCFSIM2_GPIOFUNC	(MCF_MBAR2 + 0x00C)	/* GPIO function */
+#define MCFSIM2_GPIO1READ	(MCF_MBAR2 + 0x0B0)	/* GPIO1 read values */
+#define MCFSIM2_GPIO1WRITE	(MCF_MBAR2 + 0x0B4)	/* GPIO1 write values */
+#define MCFSIM2_GPIO1ENABLE	(MCF_MBAR2 + 0x0B8)	/* GPIO1 enabled */
+#define MCFSIM2_GPIO1FUNC	(MCF_MBAR2 + 0x0BC)	/* GPIO1 function */
+
+#define MCFSIM2_GPIOINTSTAT	(MCF_MBAR2 + 0xc0)	/* GPIO intr status */
+#define MCFSIM2_GPIOINTCLEAR	(MCF_MBAR2 + 0xc0)	/* GPIO intr clear */
+#define MCFSIM2_GPIOINTENABLE	(MCF_MBAR2 + 0xc4)	/* GPIO intr enable */
+
+#define MCFSIM2_DMAROUTE	(MCF_MBAR2 + 0x188)     /* DMA routing */
+#define MCFSIM2_IDECONFIG1	(MCF_MBAR2 + 0x18c)	/* IDEconfig1 */
+#define MCFSIM2_IDECONFIG2	(MCF_MBAR2 + 0x190)	/* IDEconfig2 */
+
+/*
+ * Generic GPIO support
+ */
+#define MCFGPIO_PIN_MAX		64
+#ifdef CONFIG_M5249
+#define MCFGPIO_IRQ_MAX		-1
+#define MCFGPIO_IRQ_VECBASE	-1
+#else
+#define MCFGPIO_IRQ_MAX		7
+#define MCFGPIO_IRQ_VECBASE	MCF_IRQ_GPIO0
+#endif
+
+/****************************************************************************/
+
+#ifdef __ASSEMBLER__
+#ifdef CONFIG_M5249C3
+/*
+ *	The M5249C3 board needs a little help getting all its SIM devices
+ *	initialized at kernel start time. dBUG doesn't set much up, so
+ *	we need to do it manually.
+ */
+.macro m5249c3_setup
+	/*
+	 *	Set MBAR1 and MBAR2, just incase they are not set.
+	 */
+	movel	#0x10000001,%a0
+	movec	%a0,%MBAR			/* map MBAR region */
+	subql	#1,%a0				/* get MBAR address in a0 */
+
+	movel	#0x80000001,%a1
+	movec	%a1,#3086			/* map MBAR2 region */
+	subql	#1,%a1				/* get MBAR2 address in a1 */
+
+	/*
+	 *      Move secondary interrupts to their base (128).
+	 */
+	moveb	#MCFINTC2_VECBASE,%d0
+	moveb	%d0,0x16b(%a1)			/* interrupt base register */
+
+	/*
+	 *      Work around broken CSMR0/DRAM vector problem.
+	 */
+	movel	#0x001F0021,%d0			/* disable C/I bit */
+	movel	%d0,0x84(%a0)			/* set CSMR0 */
+
+	/*
+	 *	Disable the PLL firstly. (Who knows what state it is
+	 *	in here!).
+	 */
+	movel	0x180(%a1),%d0			/* get current PLL value */
+	andl	#0xfffffffe,%d0			/* PLL bypass first */
+	movel	%d0,0x180(%a1)			/* set PLL register */
+	nop
+
+#if CONFIG_CLOCK_FREQ == 140000000
+	/*
+	 *	Set initial clock frequency. This assumes M5249C3 board
+	 *	is fitted with 11.2896MHz crystal. It will program the
+	 *	PLL for 140MHz. Lets go fast :-)
+	 */
+	movel	#0x125a40f0,%d0			/* set for 140MHz */
+	movel	%d0,0x180(%a1)			/* set PLL register */
+	orl	#0x1,%d0
+	movel	%d0,0x180(%a1)			/* set PLL register */
+#endif
+
+	/*
+	 *	Setup CS1 for ethernet controller.
+	 *	(Setup as per M5249C3 doco).
+	 */
+	movel  #0xe0000000,%d0			/* CS1 mapped at 0xe0000000 */
+	movel  %d0,0x8c(%a0)
+	movel  #0x001f0021,%d0			/* CS1 size of 1Mb */
+	movel  %d0,0x90(%a0)
+	movew  #0x0080,%d0			/* CS1 = 16bit port, AA */
+	movew  %d0,0x96(%a0)
+
+	/*
+	 *	Setup CS2 for IDE interface.
+	 */
+	movel	#0x50000000,%d0			/* CS2 mapped at 0x50000000 */
+	movel	%d0,0x98(%a0)
+	movel	#0x001f0001,%d0			/* CS2 size of 1MB */
+	movel	%d0,0x9c(%a0)
+	movew	#0x0080,%d0			/* CS2 = 16bit, TA */
+	movew	%d0,0xa2(%a0)
+
+	movel	#0x00107000,%d0			/* IDEconfig1 */
+	movel	%d0,0x18c(%a1)
+	movel	#0x000c0400,%d0			/* IDEconfig2 */
+	movel	%d0,0x190(%a1)
+
+	movel	#0x00080000,%d0			/* GPIO19, IDE reset bit */
+	orl	%d0,0xc(%a1)			/* function GPIO19 */
+	orl	%d0,0x8(%a1)			/* enable GPIO19 as output */
+        orl	%d0,0x4(%a1)			/* de-assert IDE reset */
+.endm
+
+#define	PLATFORM_SETUP	m5249c3_setup
+
+#endif /* CONFIG_M5249C3 */
+#endif /* __ASSEMBLER__ */
+/****************************************************************************/
+#endif	/* m525xsim_h */