efDataPreprocessing main .c 吉超博 commit at 2021-01-15

efDataPreprocessing/main .c

@@ -0,0 +1,153 @@
+/*
+ * linux/arch/arm/mach-at91/board-sam9263ek.c
+ *
+ *  Copyright (C) 2005 SAN People
+ *  Copyright (C) 2007 Atmel Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ */
+
+#include <linux/types.h>
+#include <linux/gpio.h>
+#include <linux/init.h>
+#include <linux/mm.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/ads7846.h>
+#include <linux/i2c/at24.h>
+#include <linux/fb.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/leds.h>
+
+#include <video/atmel_lcdc.h>
+
+#include <asm/setup.h>
+#include <asm/mach-types.h>
+#include <asm/irq.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/at91sam9_smc.h>
+#include <mach/system_rev.h>
+
+#include "at91_aic.h"
+#include "at91_shdwc.h"
+#include "board.h"
+#include "sam9_smc.h"
+#include "generic.h"
+
+
+static void __init ek_init_early(void)
+{
+	/* Initialize processor: 16.367 MHz crystal */
+	at91_initialize(16367660);
+}
+
+/*
+ * USB Host port
+ */
+static struct at91_usbh_data __initdata ek_usbh_data = {
+	.ports		= 2,
+	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.vbus_pin_active_low = {1, 1},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
+};
+
+/*
+ * USB Device port
+ */
+static struct at91_udc_data __initdata ek_udc_data = {
+	.vbus_pin	= AT91_PIN_PA25,
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
+};
+
+
+/*
+ * ADS7846 Touchscreen
+ */
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+static int ads7843_pendown_state(void)
+{
+	return !at91_get_gpio_value(AT91_PIN_PA15);	/* Touchscreen PENIRQ */
+}
+
+static struct ads7846_platform_data ads_info = {
+	.model			= 7843,
+	.x_min			= 150,
+	.x_max			= 3830,
+	.y_min			= 190,
+	.y_max			= 3830,
+	.vref_delay_usecs	= 100,
+	.x_plate_ohms		= 450,
+	.y_plate_ohms		= 250,
+	.pressure_max		= 15000,
+	.debounce_max		= 1,
+	.debounce_rep		= 0,
+	.debounce_tol		= (~0),
+	.get_pendown_state	= ads7843_pendown_state,
+};
+
+static void __init ek_add_device_ts(void)
+{
+	at91_set_B_periph(AT91_PIN_PA15, 1);	/* External IRQ1, with pullup */
+	at91_set_gpio_input(AT91_PIN_PA31, 1);	/* Touchscreen BUSY signal */
+}
+#else
+static void __init ek_add_device_ts(void) {}
+#endif
+
+/*
+ * SPI devices.
+ */
+static struct spi_board_info ek_spi_devices[] = {
+#if defined(CONFIG_MTD_AT91_DATAFLASH_CARD)
+	{	/* DataFlash card */
+		.modalias	= "mtd_dataflash",
+		.chip_select	= 0,
+		.max_speed_hz	= 15 * 1000 * 1000,
+		.bus_num	= 0,
+	},
+#endif
+#if defined(CONFIG_TOUCHSCREEN_ADS7846) || defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
+	{
+		.modalias	= "ads7846",
+		.chip_select	= 3,
+		.max_speed_hz	= 125000 * 26,	/* (max sample rate @ 3V) * (cmd + data + overhead) */
+		.bus_num	= 0,
+		.platform_data	= &ads_info,
+		.irq		= NR_IRQS_LEGACY + AT91SAM9263_ID_IRQ1,
+	},
+#endif
+};
+
+
+/*
+ * MCI (SD/MMC)
+ */
+static struct mci_platform_data __initdata mci1_data = {
+	.slot[0] = {
+		.bus_width	= 4,
+		.detect_pin	= AT91_PIN_PE18,
+		.wp_pin		= AT91_PIN_PE19,
+	},
+};
+
+
+/*