efDataDiscreteRateMining analysisDataOperation.h 沈瑞清 commit at 2020-11-05

efDataDiscreteRateMining/databaseOperation/analysisDataOperation.h

@@ -577,3 +577,167 @@
                 	        	/* Service request (read)          */
 #define HSSR0_RFS	0x00000010	/* Receive FIFO 2/5-to-3/5-full or */
                 	        	/* more Service request (read)     */
+#define HSSR0_FRE	0x00000020	/* receive FRaming Error           */
+
+#define HSSR1_RSY	0x00000001	/* Receiver SYnchronized (read)    */
+#define HSSR1_TBY	0x00000002	/* Transmitter BusY (read)         */
+#define HSSR1_RNE	0x00000004	/* Receive FIFO Not Empty (read)   */
+#define HSSR1_TNF	0x00000008	/* Transmit FIFO Not Full (read)   */
+#define HSSR1_EOF	0x00000010	/* receive End-Of-Frame (read)     */
+#define HSSR1_CRE	0x00000020	/* receive CRC Error (read)        */
+#define HSSR1_ROR	0x00000040	/* Receive FIFO Over-Run (read)    */
+
+#define HSCR2_TXP	0x00040000	/* Transmit data Polarity (TXD_2)  */
+#define HSCR2_TrDataL	(HSCR2_TXP*0)	/*  Transmit Data active Low       */
+                	        	/*  (inverted)                     */
+#define HSCR2_TrDataH	(HSCR2_TXP*1)	/*  Transmit Data active High      */
+                	        	/*  (non-inverted)                 */
+#define HSCR2_RXP	0x00080000	/* Receive data Polarity (RXD_2)   */
+#define HSCR2_RcDataL	(HSCR2_RXP*0)	/*  Receive Data active Low        */
+                	        	/*  (inverted)                     */
+#define HSCR2_RcDataH	(HSCR2_RXP*1)	/*  Receive Data active High       */
+                	        	/*  (non-inverted)                 */
+
+
+/*
+ * Multi-media Communications Port (MCP) control registers
+ *
+ * Registers
+ *    Ser4MCCR0 	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Control Register 0 (read/write).
+ *    Ser4MCDR0 	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Data Register 0 (audio, read/write).
+ *    Ser4MCDR1 	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Data Register 1 (telecom, read/write).
+ *    Ser4MCDR2 	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Data Register 2 (CODEC registers, read/write).
+ *    Ser4MCSR  	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Status Register (read/write).
+ *    Ser4MCCR1 	Serial port 4 Multi-media Communications Port (MCP)
+ *              	Control Register 1 (read/write).
+ *              	[The MCCR1 register is only implemented in
+ *              	versions 2.0 (rev. = 8) and higher of the StrongARM
+ *              	SA-1100.]
+ *
+ * Clocks
+ *    fmc, Tmc  	Frequency, period of the MCP communication (10 MHz,
+ *              	12 MHz, or GPIO [21]).
+ *    faud, Taud	Frequency, period of the audio sampling.
+ *    ftcm, Ttcm	Frequency, period of the telecom sampling.
+ */
+
+#define Ser4MCCR0	__REG(0x80060000)  /* Ser. port 4 MCP Control Reg. 0 */
+#define Ser4MCDR0	__REG(0x80060008)  /* Ser. port 4 MCP Data Reg. 0 (audio) */
+#define Ser4MCDR1	__REG(0x8006000C)  /* Ser. port 4 MCP Data Reg. 1 (telecom) */
+#define Ser4MCDR2	__REG(0x80060010)  /* Ser. port 4 MCP Data Reg. 2 (CODEC reg.) */
+#define Ser4MCSR	__REG(0x80060018)  /* Ser. port 4 MCP Status Reg. */
+#define Ser4MCCR1	__REG(0x90060030)  /* Ser. port 4 MCP Control Reg. 1 */
+
+#define MCCR0_ASD	Fld (7, 0)	/* Audio Sampling rate Divisor/32  */
+                	        	/* [6..127]                        */
+                	        	/* faud = fmc/(32*ASD)             */
+                	        	/* Taud = 32*ASD*Tmc               */
+#define MCCR0_AudSmpDiv(Div)    	/*  Audio Sampling rate Divisor    */ \
+                	        	/*  [192..4064]                    */ \
+                	((Div)/32 << FShft (MCCR0_ASD))
+                	        	/*  faud = fmc/(32*Floor (Div/32)) */
+                	        	/*  Taud = 32*Floor (Div/32)*Tmc   */
+#define MCCR0_CeilAudSmpDiv(Div)	/*  Ceil. of AudSmpDiv [192..4064] */ \
+                	(((Div) + 31)/32 << FShft (MCCR0_ASD))
+                	        	/*  faud = fmc/(32*Ceil (Div/32))  */
+                	        	/*  Taud = 32*Ceil (Div/32)*Tmc    */
+#define MCCR0_TSD	Fld (7, 8)	/* Telecom Sampling rate           */
+                	        	/* Divisor/32 [16..127]            */
+                	        	/* ftcm = fmc/(32*TSD)             */
+                	        	/* Ttcm = 32*TSD*Tmc               */
+#define MCCR0_TcmSmpDiv(Div)    	/*  Telecom Sampling rate Divisor  */ \
+                	        	/*  [512..4064]                    */ \
+                	((Div)/32 << FShft (MCCR0_TSD))
+                	        	/*  ftcm = fmc/(32*Floor (Div/32)) */
+                	        	/*  Ttcm = 32*Floor (Div/32)*Tmc   */
+#define MCCR0_CeilTcmSmpDiv(Div)	/*  Ceil. of TcmSmpDiv [512..4064] */ \
+                	(((Div) + 31)/32 << FShft (MCCR0_TSD))
+                	        	/*  ftcm = fmc/(32*Ceil (Div/32))  */
+                	        	/*  Ttcm = 32*Ceil (Div/32)*Tmc    */
+#define MCCR0_MCE	0x00010000	/* MCP Enable                      */
+#define MCCR0_ECS	0x00020000	/* External Clock Select           */
+#define MCCR0_IntClk	(MCCR0_ECS*0)	/*  Internal Clock (10 or 12 MHz)  */
+#define MCCR0_ExtClk	(MCCR0_ECS*1)	/*  External Clock (GPIO [21])     */
+#define MCCR0_ADM	0x00040000	/* A/D (audio/telecom) data        */
+                	        	/* sampling/storing Mode           */
+#define MCCR0_VldBit	(MCCR0_ADM*0)	/*  Valid Bit storing mode         */
+#define MCCR0_SmpCnt	(MCCR0_ADM*1)	/*  Sampling Counter storing mode  */
+#define MCCR0_TTE	0x00080000	/* Telecom Transmit FIFO 1/2-full  */
+                	        	/* or less interrupt Enable        */
+#define MCCR0_TRE	0x00100000	/* Telecom Receive FIFO 1/2-full   */
+                	        	/* or more interrupt Enable        */
+#define MCCR0_ATE	0x00200000	/* Audio Transmit FIFO 1/2-full    */
+                	        	/* or less interrupt Enable        */
+#define MCCR0_ARE	0x00400000	/* Audio Receive FIFO 1/2-full or  */
+                	        	/* more interrupt Enable           */
+#define MCCR0_LBM	0x00800000	/* Look-Back Mode                  */
+#define MCCR0_ECP	Fld (2, 24)	/* External Clock Prescaler - 1    */
+#define MCCR0_ExtClkDiv(Div)    	/*  External Clock Divisor [1..4]  */ \
+                	(((Div) - 1) << FShft (MCCR0_ECP))
+
+#define MCDR0_DATA	Fld (12, 4)	/* receive/transmit audio DATA     */
+                	        	/* FIFOs                           */
+
+#define MCDR1_DATA	Fld (14, 2)	/* receive/transmit telecom DATA   */
+                	        	/* FIFOs                           */
+
+                	        	/* receive/transmit CODEC reg.     */
+                	        	/* FIFOs:                          */
+#define MCDR2_DATA	Fld (16, 0)	/*  reg. DATA                      */
+#define MCDR2_RW	0x00010000	/*  reg. Read/Write (transmit)     */
+#define MCDR2_Rd	(MCDR2_RW*0)	/*   reg. Read                     */
+#define MCDR2_Wr	(MCDR2_RW*1)	/*   reg. Write                    */
+#define MCDR2_ADD	Fld (4, 17)	/*  reg. ADDress                   */
+
+#define MCSR_ATS	0x00000001	/* Audio Transmit FIFO 1/2-full    */
+                	        	/* or less Service request (read)  */
+#define MCSR_ARS	0x00000002	/* Audio Receive FIFO 1/2-full or  */
+                	        	/* more Service request (read)     */
+#define MCSR_TTS	0x00000004	/* Telecom Transmit FIFO 1/2-full  */
+                	        	/* or less Service request (read)  */
+#define MCSR_TRS	0x00000008	/* Telecom Receive FIFO 1/2-full   */
+                	        	/* or more Service request (read)  */
+#define MCSR_ATU	0x00000010	/* Audio Transmit FIFO Under-run   */
+#define MCSR_ARO	0x00000020	/* Audio Receive FIFO Over-run     */
+#define MCSR_TTU	0x00000040	/* Telecom Transmit FIFO Under-run */
+#define MCSR_TRO	0x00000080	/* Telecom Receive FIFO Over-run   */
+#define MCSR_ANF	0x00000100	/* Audio transmit FIFO Not Full    */
+                	        	/* (read)                          */
+#define MCSR_ANE	0x00000200	/* Audio receive FIFO Not Empty    */
+                	        	/* (read)                          */
+#define MCSR_TNF	0x00000400	/* Telecom transmit FIFO Not Full  */
+                	        	/* (read)                          */
+#define MCSR_TNE	0x00000800	/* Telecom receive FIFO Not Empty  */
+                	        	/* (read)                          */
+#define MCSR_CWC	0x00001000	/* CODEC register Write Completed  */
+                	        	/* (read)                          */
+#define MCSR_CRC	0x00002000	/* CODEC register Read Completed   */
+                	        	/* (read)                          */
+#define MCSR_ACE	0x00004000	/* Audio CODEC Enabled (read)      */
+#define MCSR_TCE	0x00008000	/* Telecom CODEC Enabled (read)    */
+
+#define MCCR1_CFS	0x00100000	/* Clock Freq. Select              */
+#define MCCR1_F12MHz	(MCCR1_CFS*0)	/*  Freq. (fmc) = ~ 12 MHz         */
+                	        	/*  (11.981 MHz)                   */
+#define MCCR1_F10MHz	(MCCR1_CFS*1)	/*  Freq. (fmc) = ~ 10 MHz         */
+                	        	/*  (9.585 MHz)                    */
+
+
+/*
+ * Synchronous Serial Port (SSP) control registers
+ *
+ * Registers
+ *    Ser4SSCR0 	Serial port 4 Synchronous Serial Port (SSP) Control
+ *              	Register 0 (read/write).
+ *    Ser4SSCR1 	Serial port 4 Synchronous Serial Port (SSP) Control
+ *              	Register 1 (read/write).
+ *              	[Bits SPO and SP are only implemented in versions 2.0
+ *              	(rev. = 8) and higher of the StrongARM SA-1100.]
+ *    Ser4SSDR  	Serial port 4 Synchronous Serial Port (SSP) Data
+ *              	Register (read/write).
+ *    Ser4SSSR  	Serial port 4 Synchronous Serial Port (SSP) Status