efDataDiscreteRateMining calculationDeviationOfLeakageCurrent.c 张婷 commit at 2020-09-07

efDataDiscreteRateMining/standardDeviationCalculation/calculationDeviationOfLeakageCurrent.c

@@ -232,3 +232,143 @@ static void assabet_lcd_power(int on)
 
 /*
  * The assabet uses a sharp LQ039Q2DS54 LCD module.  It is actually
+ * takes an RGB666 signal, but we provide it with an RGB565 signal
+ * instead (def_rgb_16).
+ */
+static struct sa1100fb_mach_info lq039q2ds54_info = {
+	.pixclock	= 171521,	.bpp		= 16,
+	.xres		= 320,		.yres		= 240,
+
+	.hsync_len	= 5,		.vsync_len	= 1,
+	.left_margin	= 61,		.upper_margin	= 3,
+	.right_margin	= 9,		.lower_margin	= 0,
+
+	.sync		= FB_SYNC_HOR_HIGH_ACT | FB_SYNC_VERT_HIGH_ACT,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(2),
+
+	.backlight_power = assabet_lcd_backlight_power,
+	.lcd_power = assabet_lcd_power,
+	.set_visual = assabet_lcd_set_visual,
+};
+#else
+static void assabet_pal_backlight_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LIGHT_ON);
+}
+
+static void assabet_pal_power(int on)
+{
+	ASSABET_BCR_clear(ASSABET_BCR_LCD_ON);
+}
+
+static struct sa1100fb_mach_info pal_info = {
+	.pixclock	= 67797,	.bpp		= 16,
+	.xres		= 640,		.yres		= 512,
+
+	.hsync_len	= 64,		.vsync_len	= 6,
+	.left_margin	= 125,		.upper_margin	= 70,
+	.right_margin	= 115,		.lower_margin	= 36,
+
+	.lccr0		= LCCR0_Color | LCCR0_Sngl | LCCR0_Act,
+	.lccr3		= LCCR3_OutEnH | LCCR3_PixRsEdg | LCCR3_ACBsDiv(512),
+
+	.backlight_power = assabet_pal_backlight_power,
+	.lcd_power = assabet_pal_power,
+	.set_visual = assabet_lcd_set_visual,
+};
+#endif
+
+#ifdef CONFIG_ASSABET_NEPONSET
+static struct resource neponset_resources[] = {
+	DEFINE_RES_MEM(0x10000000, 0x08000000),
+	DEFINE_RES_MEM(0x18000000, 0x04000000),
+	DEFINE_RES_MEM(0x40000000, SZ_8K),
+	DEFINE_RES_IRQ(IRQ_GPIO25),
+};
+#endif
+
+static void __init assabet_init(void)
+{
+	/*
+	 * Ensure that the power supply is in "high power" mode.
+	 */
+	GPSR = GPIO_GPIO16;
+	GPDR |= GPIO_GPIO16;
+
+	/*
+	 * Ensure that these pins are set as outputs and are driving
+	 * logic 0.  This ensures that we won't inadvertently toggle
+	 * the WS latch in the CPLD, and we don't float causing
+	 * excessive power drain.  --rmk
+	 */
+	GPCR = GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+	GPDR |= GPIO_SSP_TXD | GPIO_SSP_SCLK | GPIO_SSP_SFRM;
+
+	/*
+	 * Also set GPIO27 as an output; this is used to clock UART3
+	 * via the FPGA and as otherwise has no pullups or pulldowns,
+	 * so stop it floating.
+	 */
+	GPCR = GPIO_GPIO27;
+	GPDR |= GPIO_GPIO27;
+
+	/*
+	 * Set up registers for sleep mode.
+	 */
+	PWER = PWER_GPIO0;
+	PGSR = 0;
+	PCFR = 0;
+	PSDR = 0;
+	PPDR |= PPC_TXD3 | PPC_TXD1;
+	PPSR |= PPC_TXD3 | PPC_TXD1;
+
+	sa11x0_ppc_configure_mcp();
+
+	if (machine_has_neponset()) {
+		/*
+		 * Angel sets this, but other bootloaders may not.
+		 *
+		 * This must precede any driver calls to BCR_set()
+		 * or BCR_clear().
+		 */
+		ASSABET_BCR = BCR_value = ASSABET_BCR_DB1111;
+
+#ifndef CONFIG_ASSABET_NEPONSET
+		printk( "Warning: Neponset detected but full support "
+			"hasn't been configured in the kernel\n" );
+#else
+		platform_device_register_simple("neponset", 0,
+			neponset_resources, ARRAY_SIZE(neponset_resources));
+#endif
+	}
+
+#ifndef ASSABET_PAL_VIDEO
+	sa11x0_register_lcd(&lq039q2ds54_info);
+#else
+	sa11x0_register_lcd(&pal_video);
+#endif
+	sa11x0_register_mtd(&assabet_flash_data, assabet_flash_resources,
+			    ARRAY_SIZE(assabet_flash_resources));
+	sa11x0_register_irda(&assabet_irda_data);
+	sa11x0_register_mcp(&assabet_mcp_data);
+}
+
+/*
+ * On Assabet, we must probe for the Neponset board _before_
+ * paging_init() has occurred to actually determine the amount
+ * of RAM available.  To do so, we map the appropriate IO section
+ * in the page table here in order to access GPIO registers.
+ */
+static void __init map_sa1100_gpio_regs( void )
+{
+	unsigned long phys = __PREG(GPLR) & PMD_MASK;
+	unsigned long virt = (unsigned long)io_p2v(phys);
+	int prot = PMD_TYPE_SECT | PMD_SECT_AP_WRITE | PMD_DOMAIN(DOMAIN_IO);
+	pmd_t *pmd;
+
+	pmd = pmd_offset(pud_offset(pgd_offset_k(virt), virt), virt);
+	*pmd = __pmd(phys | prot);
+	flush_pmd_entry(pmd);
+}