waterDataDiscreteRateMining averageLiquidLevel.h 姚强 commit at 2020-11-18

waterDataDiscreteRateMining/averageCalculation/averageLiquidLevel.h

@@ -70,3 +70,115 @@
 				 * on the PA7 input pin (CHRP). Output.
 				 * [MkLinux] "Drive Select"
 				 *  (with 0x20 being 'disk head select')
+				 */
+#define VIA1A_vSync	0x08    /* [CHRP] Sync Modem: modem clock select:
+                                 * 1: select the external serial clock to
+				 *    drive the SCC's /RTxCA pin.
+				 * 0: Select the 3.6864MHz clock to drive
+				 *    the SCC cell.
+				 * [Macintosh Family] Correct on all but IIfx
+				 */
+
+/* Macintosh Family Hardware sez: bits 0-2 of VIA1A are volume control
+ * on Macs which had the PWM sound hardware.  Reserved on newer models.
+ * On IIci,IIfx, bits 1-2 are the rest of the CPU ID:
+ * bit 2: 1=IIci, 0=IIfx
+ * bit 1: 1 on both IIci and IIfx.
+ * MkLinux sez bit 0 is 'burnin flag' in this case.
+ * CHRP sez: VIA1A bits 0-2 and 5 are 'unused': if programmed as
+ * inputs, these bits will read 0.
+ */
+#define VIA1A_vVolume	0x07	/* Audio volume mask for PWM */
+#define VIA1A_CPUID0	0x02	/* CPU id bit 0 on RBV, others */
+#define VIA1A_CPUID1	0x04	/* CPU id bit 0 on RBV, others */
+#define VIA1A_CPUID2	0x10	/* CPU id bit 0 on RBV, others */
+#define VIA1A_CPUID3	0x40	/* CPU id bit 0 on RBV, others */
+
+/* Info on VIA1B is from Macintosh Family Hardware & MkLinux.
+ * CHRP offers no info. */
+#define VIA1B_vSound	0x80	/* Sound enable (for compatibility with
+				 * PWM hardware) 0=enabled.
+				 * Also, on IIci w/parity, shows parity error
+				 * 0=error, 1=OK. */
+#define VIA1B_vMystery	0x40    /* On IIci, parity enable. 0=enabled,1=disabled
+				 * On SE/30, vertical sync interrupt enable.
+				 * 0=enabled. This vSync interrupt shows up
+				 * as a slot $E interrupt. */
+#define VIA1B_vADBS2	0x20	/* ADB state input bit 1 (unused on IIfx) */
+#define VIA1B_vADBS1	0x10	/* ADB state input bit 0 (unused on IIfx) */
+#define VIA1B_vADBInt	0x08	/* ADB interrupt 0=interrupt (unused on IIfx)*/
+#define VIA1B_vRTCEnb	0x04	/* Enable Real time clock. 0=enabled. */
+#define VIA1B_vRTCClk	0x02    /* Real time clock serial-clock line. */
+#define VIA1B_vRTCData	0x01    /* Real time clock serial-data line. */
+
+/* MkLinux defines the following "VIA1 Register B contents where they
+ * differ from standard VIA1".  From the naming scheme, we assume they
+ * correspond to a VIA work-alike named 'EVR'. */
+#define	EVRB_XCVR	0x08	/* XCVR_SESSION* */
+#define	EVRB_FULL	0x10	/* VIA_FULL */
+#define	EVRB_SYSES	0x20	/* SYS_SESSION */
+#define	EVRB_AUXIE	0x00	/* Enable A/UX Interrupt Scheme */
+#define	EVRB_AUXID	0x40	/* Disable A/UX Interrupt Scheme */
+#define	EVRB_SFTWRIE	0x00	/* Software Interrupt ReQuest */
+#define	EVRB_SFTWRID	0x80	/* Software Interrupt ReQuest */
+
+/*
+ *	VIA2 A register is the interrupt lines raised off the nubus
+ *	slots.
+ *      The below info is from 'Macintosh Family Hardware.'
+ *      MkLinux calls the 'IIci internal video IRQ' below the 'RBV slot 0 irq.'
+ *      It also notes that the slot $9 IRQ is the 'Ethernet IRQ' and
+ *      defines the 'Video IRQ' as 0x40 for the 'EVR' VIA work-alike.
+ *      Perhaps OSS uses vRAM1 and vRAM2 for ADB.
+ */
+
+#define VIA2A_vRAM1	0x80	/* RAM size bit 1 (IIci: reserved) */
+#define VIA2A_vRAM0	0x40	/* RAM size bit 0 (IIci: internal video IRQ) */
+#define VIA2A_vIRQE	0x20	/* IRQ from slot $E */
+#define VIA2A_vIRQD	0x10	/* IRQ from slot $D */
+#define VIA2A_vIRQC	0x08	/* IRQ from slot $C */
+#define VIA2A_vIRQB	0x04	/* IRQ from slot $B */
+#define VIA2A_vIRQA	0x02	/* IRQ from slot $A */
+#define VIA2A_vIRQ9	0x01	/* IRQ from slot $9 */
+
+/* RAM size bits decoded as follows:
+ * bit1 bit0  size of ICs in bank A
+ *  0    0    256 kbit
+ *  0    1    1 Mbit
+ *  1    0    4 Mbit
+ *  1    1   16 Mbit
+ */
+
+/*
+ *	Register B has the fun stuff in it
+ */
+
+#define VIA2B_vVBL	0x80	/* VBL output to VIA1 (60.15Hz) driven by
+				 * timer T1.
+				 * on IIci, parity test: 0=test mode.
+				 * [MkLinux] RBV_PARODD: 1=odd,0=even. */
+#define VIA2B_vSndJck	0x40	/* External sound jack status.
+				 * 0=plug is inserted.  On SE/30, always 0 */
+#define VIA2B_vTfr0	0x20	/* Transfer mode bit 0 ack from NuBus */
+#define VIA2B_vTfr1	0x10	/* Transfer mode bit 1 ack from NuBus */
+#define VIA2B_vMode32	0x08	/* 24/32bit switch - doubles as cache flush
+				 * on II, AMU/PMMU control.
+				 *   if AMU, 0=24bit to 32bit translation
+				 *   if PMMU, 1=PMMU is accessing page table.
+				 * on SE/30 tied low.
+				 * on IIx,IIcx,IIfx, unused.
+				 * on IIci/RBV, cache control. 0=flush cache.
+				 */
+#define VIA2B_vPower	0x04	/* Power off, 0=shut off power.
+				 * on SE/30 this signal sent to PDS card. */
+#define VIA2B_vBusLk	0x02	/* Lock NuBus transactions, 0=locked.
+				 * on SE/30 sent to PDS card. */
+#define VIA2B_vCDis	0x01	/* Cache control. On IIci, 1=disable cache card
+				 * on others, 0=disable processor's instruction
+				 * and data caches. */
+
+/* Apple sez: http://developer.apple.com/technotes/ov/ov_04.html
+ * Another example of a valid function that has no ROM support is the use
+ * of the alternate video page for page-flipping animation. Since there
+ * is no ROM call to flip pages, it is necessary to go play with the
+ * right bit in the VIA chip (6522 Versatile Interface Adapter).