waterDataDiscreteRateMining synchronousMemoryDatabase.h 张芬 commit at 2021-02-24

waterDataDiscreteRateMining/varianceCalculation/synchronousMemoryDatabase.h

@@ -158,3 +158,83 @@ extern struct Linux_SBus_DMA *dma_chain;
 #define DMA_DSBL_RD_DRN  0x00001000        /* No EC drain on slave reads */
 #define DMA_BCNT_ENAB    0x00002000        /* If on, use the byte counter */
 #define DMA_TERM_CNTR    0x00004000        /* Terminal counter */
+#define DMA_CSR_DISAB    0x00010000        /* No FIFO drains during csr */
+#define DMA_SCSI_DISAB   0x00020000        /* No FIFO drains during reg */
+#define DMA_DSBL_WR_INV  0x00020000        /* No EC inval. on slave writes */
+#define DMA_ADD_ENABLE   0x00040000        /* Special ESC DVMA optimization */
+#define DMA_E_BURST8	 0x00040000	   /* ENET: SBUS r/w burst size */
+#define DMA_BRST_SZ      0x000c0000        /* SCSI: SBUS r/w burst size */
+#define DMA_BRST64       0x00080000        /* SCSI: 64byte bursts (HME on UltraSparc only) */
+#define DMA_BRST32       0x00040000        /* SCSI: 32byte bursts */
+#define DMA_BRST16       0x00000000        /* SCSI: 16byte bursts */
+#define DMA_BRST0        0x00080000        /* SCSI: no bursts (non-HME gate arrays) */
+#define DMA_ADDR_DISAB   0x00100000        /* No FIFO drains during addr */
+#define DMA_2CLKS        0x00200000        /* Each transfer = 2 clock ticks */
+#define DMA_3CLKS        0x00400000        /* Each transfer = 3 clock ticks */
+#define DMA_EN_ENETAUI   DMA_3CLKS         /* Put lance into AUI-cable mode */
+#define DMA_CNTR_DISAB   0x00800000        /* No IRQ when DMA_TERM_CNTR set */
+#define DMA_AUTO_NADDR   0x01000000        /* Use "auto nxt addr" feature */
+#define DMA_SCSI_ON      0x02000000        /* Enable SCSI dma */
+#define DMA_PARITY_OFF   0x02000000        /* HME: disable parity checking */
+#define DMA_LOADED_ADDR  0x04000000        /* Address has been loaded */
+#define DMA_LOADED_NADDR 0x08000000        /* Next address has been loaded */
+
+/* Values describing the burst-size property from the PROM */
+#define DMA_BURST1       0x01
+#define DMA_BURST2       0x02
+#define DMA_BURST4       0x04
+#define DMA_BURST8       0x08
+#define DMA_BURST16      0x10
+#define DMA_BURST32      0x20
+#define DMA_BURST64      0x40
+#define DMA_BURSTBITS    0x7f
+
+/* Determine highest possible final transfer address given a base */
+#define DMA_MAXEND(addr) (0x01000000UL-(((unsigned long)(addr))&0x00ffffffUL))
+
+/* Yes, I hack a lot of elisp in my spare time... */
+#define DMA_ERROR_P(regs)  ((((regs)->cond_reg) & DMA_HNDL_ERROR))
+#define DMA_IRQ_P(regs)    ((((regs)->cond_reg) & (DMA_HNDL_INTR | DMA_HNDL_ERROR)))
+#define DMA_WRITE_P(regs)  ((((regs)->cond_reg) & DMA_ST_WRITE))
+#define DMA_OFF(regs)      ((((regs)->cond_reg) &= (~DMA_ENABLE)))
+#define DMA_INTSOFF(regs)  ((((regs)->cond_reg) &= (~DMA_INT_ENAB)))
+#define DMA_INTSON(regs)   ((((regs)->cond_reg) |= (DMA_INT_ENAB)))
+#define DMA_PUNTFIFO(regs) ((((regs)->cond_reg) |= DMA_FIFO_INV))
+#define DMA_SETSTART(regs, addr)  ((((regs)->st_addr) = (char *) addr))
+#define DMA_BEGINDMA_W(regs) \
+        ((((regs)->cond_reg |= (DMA_ST_WRITE|DMA_ENABLE|DMA_INT_ENAB))))
+#define DMA_BEGINDMA_R(regs) \
+        ((((regs)->cond_reg |= ((DMA_ENABLE|DMA_INT_ENAB)&(~DMA_ST_WRITE)))))
+
+/* For certain DMA chips, we need to disable ints upon irq entry
+ * and turn them back on when we are done.  So in any ESP interrupt
+ * handler you *must* call DMA_IRQ_ENTRY upon entry and DMA_IRQ_EXIT
+ * when leaving the handler.  You have been warned...
+ */
+#define DMA_IRQ_ENTRY(dma, dregs) do { \
+        if(DMA_ISBROKEN(dma)) DMA_INTSOFF(dregs); \
+   } while (0)
+
+#define DMA_IRQ_EXIT(dma, dregs) do { \
+	if(DMA_ISBROKEN(dma)) DMA_INTSON(dregs); \
+   } while(0)
+
+/* Reset the friggin' thing... */
+#define DMA_RESET(dma) do { \
+	struct sparc_dma_registers *regs = dma->regs;                      \
+	/* Let the current FIFO drain itself */                            \
+	sparc_dma_pause(regs, (DMA_FIFO_ISDRAIN));                         \
+	/* Reset the logic */                                              \
+	regs->cond_reg |= (DMA_RST_SCSI);     /* assert */                 \
+	__delay(400);                         /* let the bits set ;) */    \
+	regs->cond_reg &= ~(DMA_RST_SCSI);    /* de-assert */              \
+	sparc_dma_enable_interrupts(regs);    /* Re-enable interrupts */   \
+	/* Enable FAST transfers if available */                           \
+	if(dma->revision>dvmarev1) regs->cond_reg |= DMA_3CLKS;            \
+	dma->running = 0;                                                  \
+} while(0)
+
+
+#endif /* !CONFIG_SUN3 */
+
+#endif /* !(__M68K_DVMA_H) */