efDataStatistics realizationOfDataCalculation.c 朱俊杰 commit at 2021-02-22

efDataStatistics/alarmProcessingDataCalculation/realizationOfDataCalculation.c

@@ -299,3 +299,161 @@ static struct omap_kp_platform_data h3_kp_data = {
 	.rep		= true,
 	.delay		= 9,
 	.dbounce	= true,
+};
+
+static struct platform_device h3_kp_device = {
+	.name		= "omap-keypad",
+	.id		= -1,
+	.dev		= {
+		.platform_data = &h3_kp_data,
+	},
+	.num_resources	= ARRAY_SIZE(h3_kp_resources),
+	.resource	= h3_kp_resources,
+};
+
+static struct platform_device h3_lcd_device = {
+	.name		= "lcd_h3",
+	.id		= -1,
+};
+
+static struct spi_board_info h3_spi_board_info[] __initdata = {
+	[0] = {
+		.modalias	= "tsc2101",
+		.bus_num	= 2,
+		.chip_select	= 0,
+		.max_speed_hz	= 16000000,
+		/* .platform_data	= &tsc_platform_data, */
+	},
+};
+
+static struct gpio_led h3_gpio_led_pins[] = {
+	{
+		.name		= "h3:red",
+		.default_trigger = "heartbeat",
+		.gpio		= 3,
+	},
+	{
+		.name		= "h3:green",
+		.default_trigger = "cpu0",
+		.gpio		= OMAP_MPUIO(4),
+	},
+};
+
+static struct gpio_led_platform_data h3_gpio_led_data = {
+	.leds		= h3_gpio_led_pins,
+	.num_leds	= ARRAY_SIZE(h3_gpio_led_pins),
+};
+
+static struct platform_device h3_gpio_leds = {
+	.name	= "leds-gpio",
+	.id	= -1,
+	.dev	= {
+		.platform_data = &h3_gpio_led_data,
+	},
+};
+
+static struct platform_device *devices[] __initdata = {
+	&nor_device,
+	&nand_device,
+        &smc91x_device,
+	&intlat_device,
+	&h3_kp_device,
+	&h3_lcd_device,
+	&h3_gpio_leds,
+};
+
+static struct omap_usb_config h3_usb_config __initdata = {
+	/* usb1 has a Mini-AB port and external isp1301 transceiver */
+	.otg	    = 2,
+
+#ifdef CONFIG_USB_GADGET_OMAP
+	.hmc_mode       = 19,   /* 0:host(off) 1:dev|otg 2:disabled */
+#elif  defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+	/* NONSTANDARD CABLE NEEDED (B-to-Mini-B) */
+	.hmc_mode       = 20,   /* 1:dev|otg(off) 1:host 2:disabled */
+#endif
+
+	.pins[1]	= 3,
+};
+
+static struct omap_lcd_config h3_lcd_config __initdata = {
+	.ctrl_name	= "internal",
+};
+
+static struct i2c_board_info __initdata h3_i2c_board_info[] = {
+       {
+		I2C_BOARD_INFO("tps65013", 0x48),
+       },
+	{
+		I2C_BOARD_INFO("isp1301_omap", 0x2d),
+	},
+};
+
+static void __init h3_init(void)
+{
+	h3_init_smc91x();
+
+	/* Here we assume the NOR boot config:  NOR on CS3 (possibly swapped
+	 * to address 0 by a dip switch), NAND on CS2B.  The NAND driver will
+	 * notice whether a NAND chip is enabled at probe time.
+	 *
+	 * H3 support NAND-boot, with a dip switch to put NOR on CS2B and NAND
+	 * (which on H2 may be 16bit) on CS3.  Try detecting that in code here,
+	 * to avoid probing every possible flash configuration...
+	 */
+	nor_resource.end = nor_resource.start = omap_cs3_phys();
+	nor_resource.end += SZ_32M - 1;
+
+	nand_resource.end = nand_resource.start = OMAP_CS2B_PHYS;
+	nand_resource.end += SZ_4K - 1;
+	BUG_ON(gpio_request(H3_NAND_RB_GPIO_PIN, "NAND ready") < 0);
+	gpio_direction_input(H3_NAND_RB_GPIO_PIN);
+
+	/* GPIO10 Func_MUX_CTRL reg bit 29:27, Configure V2 to mode1 as GPIO */
+	/* GPIO10 pullup/down register, Enable pullup on GPIO10 */
+	omap_cfg_reg(V2_1710_GPIO10);
+
+	/* Mux pins for keypad */
+	omap_cfg_reg(F18_1610_KBC0);
+	omap_cfg_reg(D20_1610_KBC1);
+	omap_cfg_reg(D19_1610_KBC2);
+	omap_cfg_reg(E18_1610_KBC3);
+	omap_cfg_reg(C21_1610_KBC4);
+	omap_cfg_reg(G18_1610_KBR0);
+	omap_cfg_reg(F19_1610_KBR1);
+	omap_cfg_reg(H14_1610_KBR2);
+	omap_cfg_reg(E20_1610_KBR3);
+	omap_cfg_reg(E19_1610_KBR4);
+	omap_cfg_reg(N19_1610_KBR5);
+
+	/* GPIO based LEDs */
+	omap_cfg_reg(P18_1610_GPIO3);
+	omap_cfg_reg(MPUIO4);
+
+	smc91x_resources[1].start = gpio_to_irq(40);
+	smc91x_resources[1].end = gpio_to_irq(40);
+	platform_add_devices(devices, ARRAY_SIZE(devices));
+	h3_spi_board_info[0].irq = gpio_to_irq(H3_TS_GPIO);
+	spi_register_board_info(h3_spi_board_info,
+				ARRAY_SIZE(h3_spi_board_info));
+	omap_serial_init();
+	h3_i2c_board_info[1].irq = gpio_to_irq(14);
+	omap_register_i2c_bus(1, 100, h3_i2c_board_info,
+			      ARRAY_SIZE(h3_i2c_board_info));
+	omap1_usb_init(&h3_usb_config);
+	h3_mmc_init();
+
+	omapfb_set_lcd_config(&h3_lcd_config);
+}
+
+MACHINE_START(OMAP_H3, "TI OMAP1710 H3 board")
+	/* Maintainer: Texas Instruments, Inc. */
+	.atag_offset	= 0x100,
+	.map_io		= omap16xx_map_io,
+	.init_early     = omap1_init_early,
+	.init_irq	= omap1_init_irq,
+	.init_machine	= h3_init,
+	.init_late	= omap1_init_late,
+	.timer		= &omap1_timer,
+	.restart	= omap1_restart,
+MACHINE_END