efDataDiscreteRateMining cablePowerDataOperation.h 韩正义 commit at 2021-01-08

efDataDiscreteRateMining/databaseOperation/cablePowerDataOperation.h

@@ -101,3 +101,100 @@
 #define U2DOTGUCR_RUN	(1    << 25)	/* RUN */
 #define U2DOTGUCR_RNW	(1    << 24)	/* Read or Write operation */
 #define U2DOTGUCR_ADDR	(0x3f << 16)	/* Address of the ULPI PHY register */
+#define U2DOTGUCR_WDATA	(0xff << 8)	/* The data for a WRITE command */
+#define U2DOTGUCR_RDATA	(0xff << 0)	/* The data for a READ command */
+
+#define U2DP3CR		(0x0034)	/* U2D Port 3 Control Register */
+#define U2DP3CR_P2SS	(0x3 << 8)	/* Host Port 2 Serial Mode Select */
+#define U2DP3CR_P3SS	(0x7 << 4)	/* Host Port 3 Serial Mode Select */
+#define U2DP3CR_VPVMBEN	(0x1 << 2)	/* Host Port 3 Vp/Vm Block Enable */
+#define U2DP3CR_CFG	(0x3 << 0)	/* Host Port 3 Configuration */
+
+#define U2DCSR0		(0x0100)	/* U2D Control/Status Register - Endpoint 0 */
+#define U2DCSR0_IPA	(1 << 8)	/* IN Packet Adjusted */
+#define U2DCSR0_SA	(1 << 7)	/* SETUP Active */
+#define U2DCSR0_RNE	(1 << 6)	/* Receive FIFO Not Empty */
+#define U2DCSR0_FST	(1 << 5)	/* Force Stall */
+#define U2DCSR0_SST	(1 << 4)	/* Send Stall */
+#define U2DCSR0_DME	(1 << 3)	/* DMA Enable */
+#define U2DCSR0_FTF	(1 << 2)	/* Flush Transmit FIFO */
+#define U2DCSR0_IPR	(1 << 1)	/* IN Packet Ready */
+#define U2DCSR0_OPC	(1 << 0)	/* OUT Packet Complete */
+
+#define U2DCSR(x)	(0x0100 + ((x) << 2))	/* U2D Control/Status Register - Endpoint x */
+#define U2DCSR_BF	(1 << 10)	/* Buffer Full, for OUT eps */
+#define U2DCSR_BE	(1 << 10)	/* Buffer Empty, for IN eps */
+#define U2DCSR_DPE	(1 << 9)	/* Data Packet Error, for ISO eps only */
+#define U2DCSR_FEF	(1 << 8)	/* Flush Endpoint FIFO */
+#define U2DCSR_SP	(1 << 7)	/* Short Packet Control/Status, for OUT eps only, readonly */
+#define U2DCSR_BNE	(1 << 6)	/* Buffer Not Empty, for OUT eps */
+#define U2DCSR_BNF	(1 << 6)	/* Buffer Not Full, for IN eps */
+#define U2DCSR_FST	(1 << 5)	/* Force STALL, write 1 set */
+#define U2DCSR_SST	(1 << 4)	/* Sent STALL, write 1 clear */
+#define U2DCSR_DME	(1 << 3)	/* DMA Enable */
+#define U2DCSR_TRN	(1 << 2)	/* Tx/Rx NAK, write 1 clear */
+#define U2DCSR_PC	(1 << 1)	/* Packet Complete, write 1 clear */
+#define U2DCSR_FS	(1 << 0)	/* FIFO needs Service */
+
+#define U2DBCR0		(0x0200)		/* U2D Byte Count Register - Endpoint 0 */
+#define U2DBCR(x)	(0x0200 + ((x) << 2))	/* U2D Byte Count Register - Endpoint x */
+
+#define U2DDR0		(0x0300)		/* U2D Data Register - Endpoint 0 */
+
+#define U2DEPCR(x)	(0x0400 + ((x) << 2))	/* U2D Configuration Register - Endpoint x */
+#define U2DEPCR_EE	(1 << 0)		/* Endpoint Enable */
+#define U2DEPCR_BS_MASK	(0x3FE)			/* Buffer Size, BS*8=FIFO size, max 8184B = 8KB */
+
+#define U2DSCA		(0x0500)		/* U2D Setup Command Address */
+#define U2DSCA_VALUE	(0x0120)
+
+#define U2DEN0		(0x0504)		/* U2D Endpoint Information Register - Endpoint 0 */
+#define U2DEN(x)	(0x0504 + ((x) << 2))	/* U2D Endpoint Information Register - Endpoint x */
+
+/* U2DMA registers */
+#define U2DMACSR0		(0x1000)	/* U2DMA Control/Status Register - Channel 0 */
+#define U2DMACSR(x)		(0x1000 + ((x) << 2))	/* U2DMA Control/Status Register - Channel x */
+#define U2DMACSR_RUN		(1 << 31)	/* Run Bit (read / write) */
+#define U2DMACSR_STOPIRQEN	(1 << 29)	/* Stop Interrupt Enable (read / write) */
+#define U2DMACSR_EORIRQEN	(1 << 28)	/* End of Receive Interrupt Enable (R/W) */
+#define U2DMACSR_EORJMPEN	(1 << 27)	/* Jump to next descriptor on EOR */
+#define U2DMACSR_EORSTOPEN	(1 << 26)	/* STOP on an EOR */
+#define U2DMACSR_RASIRQEN	(1 << 23)	/* Request After Cnannel Stopped Interrupt Enable */
+#define U2DMACSR_MASKRUN	(1 << 22)	/* Mask Run */
+#define U2DMACSR_SCEMC		(3 << 18)	/* System Bus Split Completion Error Message Class */
+#define U2DMACSR_SCEMI		(0x1f << 13)	/* System Bus Split Completion Error Message Index */
+#define U2DMACSR_BUSERRTYPE	(7 << 10)	/* PX Bus Error Type */
+#define U2DMACSR_EORINTR	(1 << 9)	/* End Of Receive */
+#define U2DMACSR_REQPEND	(1 << 8)	/* Request Pending */
+#define U2DMACSR_RASINTR	(1 << 4)	/* Request After Channel Stopped (read / write 1 clear) */
+#define U2DMACSR_STOPINTR	(1 << 3)	/* Stop Interrupt (read only) */
+#define U2DMACSR_ENDINTR	(1 << 2)	/* End Interrupt (read / write 1 clear) */
+#define U2DMACSR_STARTINTR	(1 << 1)	/* Start Interrupt (read / write 1 clear) */
+#define U2DMACSR_BUSERRINTR	(1 << 0)	/* Bus Error Interrupt (read / write 1 clear) */
+
+#define U2DMACR		(0x1080)		/* U2DMA Control Register */
+#define U2DMAINT	(0x10F0)		/* U2DMA Interrupt Register */
+
+#define U2DMABR0	(0x1100)		/* U2DMA Branch Register - Channel 0 */
+#define U2DMABR(x)      (0x1100 + (x) << 2)	/* U2DMA Branch Register - Channel x */
+
+#define U2DMADADR0      (0x1200)		/* U2DMA Descriptor Address Register - Channel 0 */
+#define U2DMADADR(x)    (0x1200 + (x) * 0x10)	/* U2DMA Descriptor Address Register - Channel x */
+
+#define U2DMADADR_STOP	(1U << 0)
+
+#define U2DMASADR0	(0x1204)		/* U2DMA Source Address Register - Channel 0 */
+#define U2DMASADR(x)	(0x1204 + (x) * 0x10)	/* U2DMA Source Address Register - Channel x */
+#define U2DMATADR0	(0x1208)		/* U2DMA Target Address Register - Channel 0 */
+#define U2DMATADR(x)	(0x1208 + (x) * 0x10)	/* U2DMA Target Address Register - Channel x */
+
+#define U2DMACMDR0	(0x120C)		/* U2DMA Command Address Register - Channel 0 */
+#define U2DMACMDR(x)	(0x120C + (x) * 0x10)	/* U2DMA Command Address Register - Channel x */
+
+#define U2DMACMDR_XFRDIS	(1 << 31)	/* Transfer Direction */
+#define U2DMACMDR_STARTIRQEN	(1 << 22)	/* Start Interrupt Enable */
+#define U2DMACMDR_ENDIRQEN	(1 << 21)	/* End Interrupt Enable */
+#define U2DMACMDR_PACKCOMP	(1 << 13)	/* Packet Complete */
+#define U2DMACMDR_LEN		(0x07ff)	/* length mask (max = 2K - 1) */
+
+#endif /* __ASM_ARCH_PXA3xx_U2D_H */